Use and Care Guide

WARNING: Improper use or failure to follow instructions can result in explosive
failure causing serious eye or other injury. For safe use of this product you must
read and follow all instructions. Do not leave a pressurized sprayer in the hot sun.
Heat can cause pressure build-up resulting in possible explosion. Do not store or
leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long
pants and full foot protection when spraying. Never use any tool to remove pump
if there is pressure in sprayer. Never stand with face or body over top of tank when
pumping or loosening pump to prevent ejecting pump assembly and/or solution
from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with
manufacturer’s original parts. Never spray ammable, caustic, acidic, chlorine,
bleach or other corrosive solutions or heat, pressure, or gas producing chemicals.
Always read and follow chemical manufacturer’s instructions before use with
this sprayer as some chemicals may be hazardous when used with this sprayer.
WARNING
1. Hose to Tank
2. Extension Wand to Shut-off
Loosen retaining nut from shut-o (2A). Insert extension wand into end
of shut-o until you no longer see the line marked on the end of the wand.
Tighten retaining nut (2C).
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank
outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of
these conditions are found, replace hose before using. Replace with original
manufacturer’s parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect
interior and exterior of tank for signs of deterioration of body and bottom. Any
sign of deterioration indicates possible tank weakening and could result in
explosive bursting under pressure. If any of these signs are found, discard tank
immediately and replace. Do not attempt to patch leaks, etc., as this could result
in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only
(Pump plunger 10-20 strokes and inspect for leaks).
5) Do: Direct shut-o away from you and open to make sure discharge is not
clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions),
empty tank, and proceed with Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and ttings for rust,
corrosion and pitting. If any of these conditions are found, replace aected part
with original manufacturer’s part before using.
3. Pre-Use Check
4. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on
chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overll to
accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace
pump in tank and tighten securely.
7. Care, Storage and Maintenance
1) Do: Rinse tank thoroughly with water only, empty, rell with water. Follow Filling,
Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure
that the wand and nozzle are thoroughly rinsed with water after each use.
2) Do: Open shut-o and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and
empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod
through opening in cover.
Congratulations!
You have just purchased a quality Chapin product.
Register Your Sprayer Online @ www.chapinmfg.com
Questions? Do Not Return To Store.
Call us @ 1-800-950-4458 or www.chapinmfg.com
¡Felicitaciones!
Usted acaba de adquirir un producto de calidad Chapin.
Registre su pulverizador en línea en www.chapinmfg.com
¿Preguntas? No regrese a la tienda;
llámenos al 1-800-950-4458 o visite www.chapinmfg.com
Félicitations!
Vous avez acheté un produit de qualité Chapin.
Enregistrez dès que possible votre pulvérisateur en ligne à l'adresse suivante:
www.chapinmfg.com
Questions ? Ne retournez pas au magasin.
Appelez-nous 1-800-950-4458 ou visitez le www.chapinmfg.com
016106 R0918
• Insert the outlet tube portion of the discharge assembly into the tank adapter
(Fig. 1A).
• Firmly insert the outlet tube portion into the tank adapter (Fig. 1B) leaving no gap
between the tank adapter and outlet tube adapter. Firmly tighten the retaining nut
to the tank adapter (Fig. 1C).
1A
1C
Retaining Nut -
Securely tightened.
Outlet
Tube
5. Pressurizing and Spraying
Do: Turn handle
clockwise to tighten. Push
handle down, turn 1/4
turn counterclockwise to
release.
Do: Pump until
you feel resistance.
Do: Push handle, down,
turn 1/4 turn clockwise to
lock. Begin spraying. Re-
pump sprayer as required
to maintain spray force.
Do: Turn end of nozzle
to adjust spray pattern.
5A
5C
5B
5D
1B
No Gap
Sk-1154-1
6. To Release Pressure
Sprayers with no pressure release valve
Do: With pump facing away, turn locked handle counterclockwise until air begins to
escape. Stop turning handle when you hear air escaping. Do: Point pump away until
all air has escaped.
8. Fatigue-Free Spraying
To release, press down and slide handle back.
2B
Retaining Nut
Extension
Wand
8C8D
For constant spraying, push down on shut-o handle and slide forward.
8A 8B
To Lock
To Un-Lock
Adapter
# 15410
# 15420
2A
2C
# 16100
# 16200
5A
5C
5B
OR
Line
Line is no longer
visible