Link In Zone 1 Zone 3 Active Active Zone 2 Zone 4 Active Active Model P-1044 Source 1 IR Source 2 IR Link Out PRO CHANNEL V ISION TM Source 3 IR Source 4 IR Common IR IR Data Power Source 1 Source 2 Source 3 Source 4 +24VDC P-1044 4-Source/4-Zone CAT5 Audio Matrix By 6
The P-1044 is a 4-source, 4-zone matrix switcher for Channel Vision’s CAT5 audio system. It allows up to four different sources to be played in four different zones simultaneously, making it perfect for families with a variety of listening interests. Controlling your music is easy with the P-1044’s source specific IR repeating which allows independent control of identical source components. For example, two identical CD players can be controlled independently.
Compatibility The P-1044 adheres to the same protocols as Channel Vision’s other CAT5 audio hubs to ensure maximum compatibility. However, some amplified keypads (such as the AB-114) will not provide control of source selection. If the keypad provides IR pass through (as does the AB-114), you can use an A0501 remote control to make source selections. For best results we recommend using the AB-124 amplified keypad. How it Works The P-1044 is a matrix switcher for Channel Vision’s CAT5 audio system.
Basic Application A basic system can be created with four amplified keypads (model AB-124) and four pairs of speakers. The source components can be controlled by pointing their remote control at the IR sensor in the AB-124 keypad.
Expanding The System Larger systems consisting of more than 4 zones can be created by adding a second P-1044. Use RCA ‘Y’ connectors to split the audio sources into both units. Use the provided ribbon cable to connect the “Link” terminals. This will allow IR signals received through one P-1044 to be transmitted to the other P-1044. 1 of 8 possible Amplified keypads C HANNEL V ISION Use the ribbon cable provided to connect “Link Out” from one unit to the “Link In” of the other unit.
Using Different Input Devices The P-1044 can accept signals from either a standard analog audio output (via RCA inputs) or a CAT5 audio output from one of Channel Vision’s CAT5 audio input modules. AB-311 Note: the AB-311 is compatible with many different iPods R. The iPod mini is shown for reference only.
Integrating the P-1044 with other products Many different components can be integrated together. The system below integrates a single-source CAT5 audio hub (model P-1014) as well as telephone paging modules. The keypads connected to the P-1014 will act as sub-zones to the P-1044. These sub-zones will all play the same audio which is perfect for common areas such as hallways, bathrooms, kitchen, or dinning room. Adding the C-0920 and P-0925 allows paging to occur in these common areas.
Using the A0501 remote control The A0501 is designed to allow you to control your P-1044 without having to touch the buttons on the AB-124. Simply point the A0501 remote control at the IR sensor located at the bottom of the AB-124 and press the desired button. Zone Power - Turns off the output of the P-1044. Power - Turns off the AB-124.
Mounting Options The P-1300 from Channel Vision’s Pro-series product line is the perfect home for the P-1044. The P-1300 is a hinged plate designed to fit into a standard 19” rack. Zone 1 Zone 3 Active Active Zone 2 Link In Source 1 IR Zone 4 Active Model P-1044 Source 2 IR Active Link Out PRO CHANNEL V ISION TM Source 3 IR Source 4 IR The P-1300 hinges open to maintain a clean look and provide easy access for servicing equipment.
Connection Tips and Troubleshooting 1) Be sure you have connected the CAT5 cable correctly. Note that the stripe/solid pattern should match the labels on the product. Misswiring can cause distorted sound or prevent the system from working at all! 2) Be sure you have connected the speakers in phase. Follow the label on the product. Out of phase speakers can rob the system of its bass, especially when driving dual-voice-coil speakers.
Stripping and Connecting CAT5 Wire CAT5 cable should be stripped with a proper stripping tool, such as Channel Vision’s J-110 tool. 1. Place the CAT5 between the blade and the first notch of the J-110 tool. Blade CAT5 2. Rotate the tool only once. Multiple turns will cause you to cut into the inner wires. Rotate 1 turn only 3. Inspect the inner wires for damage. If any wires are cut start over at step 1.
Channel Vision Technology will repair or replace any defect in material or workmanship which occurs during normal use of this product with new or rebuilt parts, free of charge in the USA, for two years from the date of original purchase. This is a no hassle warranty with no mail in warranty card needed. This warranty does not cover damages in shipment, failures caused by other products not supplied by Channel Vision Technology, or failures due to accident, misuse, abuse, or alteration of the equipment.
