Owner manual

112
Kit P/N 900958 Control Box Wall Mount Kit
Form No. 115074_rev. A
P/N 900958 Control Box Wall Mount Kit (for Direct Vent Option Model & Condensate Removal Option Model)
Installation Instructions: Overview: The Direct Vent Model and the Condensate Removal Model utilize a separate control box that is interwired to the dishwasher. The standard configuration calls for this box to mounted to the left-hand side of the machine; however, the control box can be mounted to the wall if desired. The following instructions describe the steps necessary to mount the control box using the parts included in the Control Box Wall Mount Kit P/N 900958.
Dish Table Dish Table
Dish Table
Dish Table
Control
Box
Dish table
Figure 1 –
The straight-through operation machine
shown with control box mounted on wall.
! VERY IMPORTANT !
The control box can only be mounted within the limits of the prewired
cables connecting the control box and the dishwasher together.
Refer to Figure 2 and Figure 3 in the Installation Instructions below
for additional information concerning the location of the control box.
Figure 2 –
For the Straight-through Operation machine,
the control box can be mounted on the right-hand or
left-hand side of the machine.
Figure 3 –
For the Corner Operation machine,
do not mount the control box in the black area shown
on the right-hand side machine.
1
Control Box Location
Refer to Figures 2 and 3. Note the gray and black shaded areas. The gray area indicates the approximate allowed location to mount the control box; black indicates the area where the control box must not be mounted. In all circumstances, the mounting location of the control box must not interfere with the operation of the hood nor prevent access to the dishwasher for servicing. The control box can only be mounted within the limits of the prewired cables connecting the control box and the dishwasher togther. NOTE: The control box and cables weigh 10 lbs./4.1 kg.
2
Check the Kit parts
Refer to Table 1 at right and make sure your kit contains the parts listed. The Wall Mount Bracket Template is located on the reverse side of this sheet.
! ATTENTION !
THE FASTENERS NEEDED TO ATTACH THE CONTROL BOX
TO THE WALL ARE NOT INCLUDED IN THE KIT.
THESE FASTENERS ARE SUPPLIED BY OTHERS.
3
Mounting the Box
Refer to Figure 4: Install the wall mount brackets (Item 1) to the back of the control box using the four screws (Item 2) supplied in the Kit. Position the control box in the desired location & make sure the cables are not overextended. Using the template, on the reverse side of this sheet, (Item 3), mark the location of the four mounting holes for the wall mount brackets on the supporting wall. See Figure 5: The control box assembly weighs 10 lbs./4.1 kg and must be mounted with the appropriate fasteners for the type of supporting wall. The fasteners are supplied by others. The control box installation is complete.
Figure 4 –
The location of the control box
must be mounted within the limits
of the interconnecting cables
without overextending the cables.
Figure 5 –
The control box assembly weighs 10 lbs/4.1 kg
and must be mounted with the appropriate
fasteners for the type of supporting wall.
The fasteners are supplied by others.
TABLE 1 - Kit Parts List
Item Part Description Qty. No. No.
1 334473 Bracket, Wall Mounting 2 2 100212 Screw, 10-32 x 3/4" Truss Head 4 3 115074 Template, Wall Mount Bracket 1 (Template on reverse side of this sheet)
1
2
3
1
Wall
fasteners
supplied
by others
Corner
Operation
Straight-through
Operation
~
6-1/2"
~
12-9/32"
Scale 1/1
Wall Mount Bracket
Template
P/N 115074
For
Model DH5000
Direct Vent Option
and
Condensate Removal Option
Electrical
Control Box
Top Wall Mount Bracket
Bottom Wall Mount Bracket
1/4" Hole 1/4" Hole
1/4" Hole 1/4" Hole
See Reverse Side for Installation Instructions