Manualshelf

Instructions / Assembly

ManualsBrandsChamberlain ManualsDoors & WindowsSingle Button Garage Door Opener Remote
12
TO ERASE ALL CODES FROM MEMORY
REMOTE CONTROL
MODEL 950ESTD-P2
To prevent possible serious injury or death from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate,
or play with remote controls.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are
no obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to
cross path of moving gate or door.
Press and hold the button
on the remote control.
“click”
“click”
Release the button
when the garage
door opener lights
blink or two clicks
are heard.
Locate the
LEARN button.
Press and
immediately release
the LEARN button.
The LEARN LED will glow
steadily for 30 seconds.
Within 30 seconds...
With the door closed,
press and hold
the remote
control button to
control the light.
Press and
hold the
LIGHT button
on the
door control.
+
Press and
hold the
LOCK button
on the
door control.
After the garage
door opener
lights flash,
release all
buttons.
+
“click”
“click”
Press and hold the LEARN button on garage door
opener or other product until the LEARN LED goes out
(approximately 6 seconds). All previous codes are
now erased. Reprogram each remote control you
wish to use.
Press the LEARN button again,
the LED will flash once.
Press the LEARN button on
the door control to enter
Programming Mode.
The command LED
will flash once.
The command LED
will flash once again.
Press and hold the button
on the remote control.
Release the button when
the garage door opener
lights blink or two clicks
are heard.
“click”
“click”
For use with Security+ 2.0
®
Garage Door Openers which have a yellow LEARN button and yellow
antenna wire, and are manufactured after 2010. The code between the remote control and the
receiver changes with each use, randomly accessing over a billion new codes. Refer to your
product manual for the location of the LEARN button.
NOTE: Your product may look different than the products illustrated in this manual.
When deactivating any unwanted remote
control codes, all previous codes will be
erased. All additional accessories will
also be erased. Refer to your product
manual for more information.
Press and hold the button
on the remote control.
“click”
“click”
Release the button
when the garage
door opener lights
blink or two clicks
are heard.
Locate the
LEARN button.
Press and
immediately release
the LEARN button.
The LEARN LED will glow
steadily for 30 seconds.
Within 30 seconds...
With the door closed,
press and hold
the remote
control button to
control the light.
Press and
hold the
LIGHT button
on the
door control.
+
Press and
hold the
LOCK button
on the
door control.
After the garage
door opener
lights flash,
release all
buttons.
+
“click”
“click”
Press and hold the LEARN button on garage door
opener or other product until the LEARN LED goes out
(approximately 6 seconds). All previous codes are
now erased. Reprogram each remote control you
wish to use.
Press the LEARN button again,
the LED will flash once.
Press the LEARN button on
the door control to enter
Programming Mode.
The command LED
will flash once.
The command LED
will flash once again.
Press and hold the button
on the remote control.
Release the button when
the garage door opener
lights blink or two clicks
are heard.
“click”
“click”
LED
PROGRAM USING THE GARAGE DOOR OPENER
PROGRAM USING THE DOOR CONTROL
Press and hold the button
on the remote control.
“click”
“click”
Release the button
when the garage
door opener lights
blink or two clicks
are heard.
Locate the
LEARN button.
Press and
immediately release
the LEARN button.
The LEARN LED will glow
steadily for 30 seconds.
Within 30 seconds...
With the door closed,
press and hold
the remote
control button to
control the light.
Press and
hold the
LIGHT button
on the
door control.
+
Press and
hold the
LOCK button
on the
door control.
After the garage
door opener
lights flash,
release all
buttons.
+
“click”
“click”
Press and hold the LEARN button on garage door
opener or other product until the LEARN LED goes out
(approximately 6 seconds). All previous codes are
now erased. Reprogram each remote control you
wish to use.
Press the LEARN button again,
the LED will flash once.
Press the LEARN button on
the door control to enter
Programming Mode.
The command LED
will flash once.
The command LED
will flash once again.
Press and hold the button
on the remote control.
Release the button when
the garage door opener
lights blink or two clicks
are heard.
“click”
“click”
WARNING: This product can expose you to chemicals including lead, which are known
to the State of California to cause cancer or birth defects or other reproductive harm. For
more information go to www.P65Warnings.ca.gov.

Summary of content (2 pages)