Installation Instructions

ManualsBrandsChamberlain Group ManualsElectronicsMain control/transceiver for use in HD Operators

Wired setup

Before digging, contact local underground utility locating companies. Use

PVC conduit to prevent damage to cables.

1. Disconnect ALL power to the operator and turn OFF the battery

switch.

2. Trench across driveway to bury the shielded twisted pair cable.

3. Connect the wires from the shielded twisted pair cable to the Com Link

terminals on the primary gate operator control board. NOTE: We

recommend that all accessories and board configurations are set on

the primary operator.

4. Route the shielded twisted pair cable to the secondary gate operator's

control board.

5. Connect the wires from the shielded twisted pair cable to the Com Link

terminals on the secondary control board (Com Link A to Com Link A

and Com Link B to Com Link B). Ground the shield of the cable to the

chassis ground of one operator.

6. Connect ALL power to the operator and turn ON the battery switch.

DUAL GATE WIRE TYPE (SHIELDED TWISTED PAIR CABLE)

22AWG up to 200feet (61m) 18AWG - 200-1000feet (61-305m)

Wire must be rated at 30 Volt minimum

Com Link Data A

Com Link Data B

Com Link Data A

Com Link Data B

Bipart delay/synchronized close

The LOCK/BIPART DELAY switch is used only with dual gate applications and serves two functions:

BIPART DELAY

Not applicable for slide gate applications.

SYNCHRONIZED CLOSE

To synchronize the closing of the gates, set the LOCK/BIPART DELAY switch to ON for both operators.

INSTALLATION

Summary of content (11 pages)

PAGE 1
INSTALLATION Wired setup DUAL GATE WIRE TYPE (SHIELDED TWISTED PAIR CABLE) 22AWG up to 200 feet (61 m) 18AWG - 200-1000 feet (61-305 m) Wire must be rated at 30 Volt minimum Before digging, contact local underground utility locating companies. Use PVC conduit to prevent damage to cables. 1. Disconnect ALL power to the operator and turn OFF the battery switch. 2. Trench across driveway to bury the shielded twisted pair cable. 3.
PAGE 2
INSTALLATION Step 9 Install the cover Before installing the cover, follow the instructions in the Adjustment section to adjust the limits, speed, and force. 1. Slide the cover over the operator. 2. Align the holes in the cover with the threaded holes in the operator's chassis and secure the cover with the provided screws. Screw Screw Step 10 Install Warning Signs Installers MUST install the UL required warning signs. The signs MUST be installed in plain view on both sides of each gate installed.
PAGE 3
ADJUSTMENT Limit, Speed, and Force Adjustment To reduce the risk of SEVERE INJURY or DEATH: l Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a moving gate. l Too much force on gate will interfere with proper operation of safety reversal system. l NEVER increase force beyond minimum amount required to move gate. l l l l NEVER use force adjustments to compensate for a binding or sticking gate.
PAGE 4
ADJUSTMENT Speed Control The SPEED CONTROL dial controls the speed of the operator. The dial is preset to minimum from the factory. Set the speed as low as possible for the intended application. Gate operating speed for HDSL24UL 0.5 ft./sec. - 1 ft./sec. Gate operating speed for HDFSL24UL 1 ft./sec. - 2 ft./sec. For dual gate setup, set the SPEED CONTROL dial on each operator to the same setting or make sure the gate that travels further is set faster than the other operator for the smoothest operation.
PAGE 5
ADJUSTMENT Adjust the Limits After both limits are set and the operator is ready to run, one limit can be adjusted independently from the other by following steps 1-3 of the Initial Limit and Force Adjustment section. After any limit adjustment: 1. Cycle the gate open and close to automatically relearn the forces. 2. Perform the Obstruction Test, see page 25. Obstruction Test 1 The operator is equipped with an inherent (built in to the operator) obstruction sensing device.
PAGE 6
PROGRAMMING Remote Controls (Not Provided) A total of 50 Security+ 2.0® remote controls or KPW250 keypads and 2 keyless entries (1 PIN for each keyless entry) can be programmed to the operator. When programming a third keyless entry to the operator, the first keyless entry will be erased to allow the third keyless entry to be programmed. When the operator’s memory is full it will exit the programming mode and the remote control will not be programmed.
PAGE 7
PROGRAMMING LiftMaster Internet Gateway (not provided) 3. Press LEARN button on gate operator - Press and release the LEARN button on the primary operator. The green XMITTER LED will light. NOTE: The operator will time out of programming mode after 180 seconds. To program the operator to the LiftMaster Internet Gateway: 1. Connect the ethernet cable to the LiftMaster Internet Gateway and the router. 2. Connect power to the LiftMaster Internet Gateway. 3. Download the myQ® App. 4.
PAGE 8
PROGRAMMING Constant Pressure Override (CPO) 6. Validate - Validate functionality by selecting Test Relay on the CAPXL display. To find out more on how to simply secure all of your access points with an easy to manage integrated system, myQ Business, please visit: www.myqbusiness.com. Constant Pressure Override is for use with KPW5 and KPW250 keypads (not provided).
PAGE 9
OPERATION Gate Operator Setup Examples The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site requirements, including all necessary entrapment protection devices.
PAGE 10
OPERATION Control Board Overview 1 SET OPEN Button: The SET OPEN button sets the OPEN limit. See Adjustment section. 2 SET CLOSE Button: The SET CLOSE button sets the CLOSE limit. See Adjustment section. 3 DIAGNOSTICS Display: The diagnostics display will show the operator type, firmware version, and codes. The operator type will display as "HD" or "HF" followed by a "24" which indicates the operator type as HDSL24UL or HDFSL24UL. The firmware version will show after the operator type, example "1.2".
PAGE 11
OPERATION Manual Disconnect 1. Set the reset switch to the RESET position. 2. Pull the manual release handle. To resume normal function, release the handle and set the switch to NORMAL OPERATION. On a dual gate application the handle must be released on both operators. Reset Switch The reset switch has the following functions: l Set the switch to the RESET position to disable gate operation. Use this switch before servicing the gate or manually disconnecting the gate. The stop LED will be illuminated.