Large Display Access Controller Model ACXL INSTALLATION MANUAL
Safety Safety Symbol and Signal Word Review When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully.
INTRODUCTION PRE-INSTALL INSTALL NETWORK INTRODUCTION Carton Inventory ..................................................................... 4 Tools Needed .......................................................................... 4 Dimensions ............................................................................. 5 System Specifications ............................................................. 5 Wire Specifications .................................................................
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Carton Inventory Controller Gooseneck Gasket Power Supply Radio Antenna (Security+ 2.
PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Dimensions FRONT VIEW SIDE VIEW 4-3/4" (10.2 cm) BACK VIEW W R R W S 18" (45.7 cm) R PROGRAMMING W S P P E P P S S 7-11/16" (17.8 cm) 7-13/32" (17.8 cm) INTRODUCTION 14" (35.6 cm) 4-1/4" (10.8 cm) E = Electrical Wiring BOTTOM VIEW P = Pedestal Mount E E E S = Surface Mount R = Radio Antenna 10-7/8" (25.4 cm) W = Wi-Fi® Antenna 14" (35.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Wire Specifications Use this chart to pull wires in preparation of your installation. DESCRIPTION OF WIRE RUN WIRE SPECIFICATION MAXIMUM RUN DISTANCE 2-Conductor 14 AWG Up to 60 feet (18.3 m) 2-Conductor 16 AWG Up to 37 feet (11.3 m) 2-Conductor 18 AWG Up to 24 feet (7.3 m) 8-Conductor, 24 AWG Twisted pair 328 feet* (100 m) 12 AWG Copper 12 feet (3.7 m) 2-Conductor 18-22 AWG Shielded 100 - 250 feet (30.5 - 76.
INTRODUCTION 1 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Internet Service The controller MUST be configured with the proper network settings to operate. NETWORK Internet service provider: Wi-Fi Network Name: Wi-Fi Password: Automatic IP addressing: DHCP (preferred setting) OR Static IP Addressing: (NOTE: Write down the following for future reference: IP, Netmask, Gateway, Primary, Secondary, Server Port) 2 SIP Provider Phone.com is the preferred SIP provider. Visit Phone.
INTRODUCTION 1 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Remove Knockouts 1. Turn the key clockwise and open the controller. 2. Identify which knockouts need to be removed based on your application. 3. Use a center punch tool to remove the knockouts. NOTE: Be careful when removing the knockouts to avoid damaging the controller components. E = Electrical Wiring To prevent damage to the controller from moisture or water: • DO NOT install during rain.
INTRODUCTION 2 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Mount Controller 1. PROGRAMMING DO Attach the goose-neck gasket (provided) if mounting to a goose-neck. 2. Mount the controller securely to a flat surface or pedestal with appropriate hardware taking care to route wiring through appropriate knockouts. NOTE: Ensure the cover can fully open to allow access after the installation is complete.
INTRODUCTION 3 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Controller Overview Wi-Fi® ANTENNA RADIO ANTENNA SENSOR BOARD CAMERA MOUNTING BRACKET POWER/INTERNET BOARD ON RADIO ANTENNA CONNECTION Wi-Fi® ANTENNA CONNECTION LOOP DETECTOR BOARD MOUNTING LOCATION CONTROL BOARD POSTAL LOCK SWITCH DOOR BOARD 1 (Doors 1 & 2) DOOR BOARD 2 (Doors 3 & 4) CAMERA LOCATION MICROPHONE LOCK DISPLAY (TOUCHSCREEN) PROXIMITY READER LOCATION POSTAL LOCK LOCATION SPEAKER 10
INTRODUCTION 4 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Power/Internet Board Overview Speaker LOOP BOARD Dip Switches (not used) Audio Postal Lock Sensor Board ON Display Backlight Display (Touch) Auxiliary Power (not used) Power Connection for Control Board Door Board 2 RADIO ANTENNA Door Board 1 POWER ETHERNET Connection to Control Board 11
INTRODUCTION 5 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Door Board Overview The ACXL has a combination of access control inputs/outputs on the Door Boards that work in conjunction to control up to 4 access points.
INTRODUCTION 6 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Install Antennas The radio antenna and Wi-Fi® antennas must be a minimum of 8 inches (20 cm) apart. Install the antennas on opposite sides of the controller. Optional antenna cable kits are available for remote antenna mounting (refer to accessories). Security+ 2.0® Radio Antenna (if applicable) Used for transmitters and wireless gate communication. 1. Secure the radio antenna to the desired knockout on the controller.
INTRODUCTION 7 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Install the Ground IMPORTANT: An earth ground rod is strongly recommended and should be no further than 12 feet (3.7 m) from the controller and use a minimum of 12 gauge wire in most cases. The type and length of earth ground rods vary by region. Contact the AHJ (Authority Having Jurisdiction) in the municipality where you plan to install the controller for correct grounding materials and installation procedures.
INTRODUCTION 8 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL PROGRAMMING Connect Power The outlet for the controller MUST be an external dedicated 120 Vac outlet located within 60 feet (18.3 m) cable run of the controller. This outlet should be wired back to its own 10 Amp minimum circuit breaker. WIRE SPECIFICATION MAXIMUM RUN DISTANCE 14 AWG Up to 60 Feet (18.3 m) 16 AWG Up to 37 Feet (11.3 m) 18 AWG Up to 24 Feet (7.3 m) 1.
