User's Manual Part 2
27
ET OP N
S T CLO E
MO E
G TE
O F
5
0
6
1 0
M N
M X
OFF
ON
N
LO E
ST P
A T HA G NG
A E MO NG
CC P R O L
C DES
TA US
I E
E T
OP
H D W
C OS
NT R
OC
C Y
OW R
N W
XP
B A D
M T R
TW R
S UP
LM T
2
5
S L R /
C A GER
J 5
B TT
DC
OW R
D R S T
L RM
G OU D
R G N WT E U ED
BR G N WT E L R D
OPEN
CLOSE
STOP
TEST
BUTTONS
RSAL
RCE
TTER
TWORK
N
LEARN
BU
SAL
XMITTER
NETWORK
S T OP N
ET LO E
OVE
A E
5
0
0
O F
ON
P T O ER
T C A GN
T ER
G T M VN
T L W
C WR O D
D G O T
C D S
T T S
FR
D
S A
C S
E
N E R
L
O
W
O W
O
2
S L R /
C A G R
5
A T
C
O ER
D E ET
L RM
R U D
BR R WT E B U R D
BR R WT YE U R D
LEARN
BU
SAL
XMITTER
NETWORK
1
2
1
2
3
S T OP N
ET C O E
OVE
A E
F
5
0
0
0
N
O F
ON
T C A GN
G T M VN
C P R O D
D
C D S
T T S
D P
X
S A O
E E
N E R
L
O
W
O W
O
S
2
S L R /
C A G R
5
A T
O ER
D E ET
L RM
BR R WT E B U R D
BR R WT YE U R D
LEARN
BU
SAL
XMITTER
NETWORK
REMOTE CONTROLS + ERASE ALL CODES
PROGRAMMING
SET PEN
SET L SE
M VE
G TE
5
0
6
O F
N
N U PO ER
A T C A GN
T ER
G T MO NG
A T OW
C PW OV
I G O T
OD S
T TU :
S C
O E
H
C O E
Y S
N ER
O K
CC R
OW R
O W
O R
MT R
R
S UP
1
L IT
2
S L R /
C A GER
J 5
B T
DC
P W R
M
G O ND
BR RN T E U R D
R G N WT E U ED
N
LEARN
BU
SAL
XMITTER
NETWORK
OPEN
CLOSE
STOP
TEST
BUTTONS
RSAL
RCE
TTER
ETWORK
1
2
3
TO ADD OR REPROGRAM A REMOTE CONTROL
(NOT PROVIDED)
Press and release the LEARN button (operator will beep and green XMITTER LED
will light).
Press the remote control button for the desired function. The operator will
automatically exit learn mode (operator will beep and green XMITTER LED will
go out) if programming is successful.
This programming step will program a single button as an open, close, and stop. To
program additional Security✚ 2.0™ remote controls, repeat the steps until all the
remote controls are programmed.
PROGRAM OPEN ONLY ON A 1-BUTTON REMOTE
CONTROL
Press and release the LEARN button (operator will beep and green XMITTER LED
will light).
Press the OPEN button.
Press the remote control button. The operator will automatically exit learn
mode (operator will beep and green XMITTER LED will go out) if programming
is successful.
To program additional Security✚ 2.0™ remote controls, repeat the steps until all the
remote controls are programmed.
PROGRAM OPEN, STOP, AND CLOSE ON A 3-BUTTON
REMOTE CONTROL
Press and release the LEARN button (operator will beep and green XMITTER LED
will light).
Press the OPEN, CLOSE, or STOP button for the desired function.
Press the remote control button for the desired function. The operator will
automatically exit learn mode (operator will beep and green XMITTER LED will
go out) if programming is successful.
To program additional buttons or Security✚ 2.0™ remote controls, repeat the steps
until all the buttons or remote controls are programmed.
1
2
Press and release the LEARN button (operator will beep and green XMITTER LED
will light).
Press and hold the LEARN button again until the green XMITTER LED goes out
(approximately 6 seconds). All remote control codes are now erased.
1
ERASE ALL CODES
1
2
3
2
REMOTE CONTROLS
1
2
3
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this transceiver are prohibited. THERE ARE
NO USER SERVICEABLE PARTS.
This device complies with Part 15 of the FCC rules and IC RSS-210. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired
operation.
This Class B digital apparatus complies with Canadian ICES-003.
AVIS : Les règles de la FCC et/ou d’Industrie Canada (IC) interdisent tout ajustement ou toute modification de ce récepteur. IL N’EXISTE
AUCUNE PIÈCE SUSCEPTIBLE D’ÊTRE ENTRETENUE PAR L’UTILISATEUR.
Cet appareil est conforme aux dispositions de la partie 15 du règlement de la FCC et de la norme IC RSS-210. Son utilisation est assujettie
aux deux conditions suivantes : (1) ce dispositif ne peut causer des interférences nuisibles, et (2) ce dispositif doit accepter toute
interférence reçue, y compris une interférence pouvant causer un fonctionnement non souhaité.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
A total of 50 Security✚ 2.0™ remote controls and 2 keyless entries (1 PIN for each keyless entry) can be programmed to the operator. NOTE: When the memory is full the
operator will exit programming mode and the remote control/keyless entry will not be programmed. The memory will need to be erased before programming any additional
remote controls/keyless entries. If installing an 86LM to extend the range of the remote controls DO NOT bend the antenna.