User's Manual

ManualsBrandsChamberlain Group ManualsElectronicsPart 15 Spread Spectrum Transmitter Transceiver

FEATURES

INTRODUCTION

FEATURES

OPERATOR FEATURES

CONTROL BOARD FEATURES

EXPANSION BOARD FEATURES

• Advanced "Centerpiece" Control Board

• EMI AC Power Surge Protection and Filter Board

- Main AC voltage input selection: 120 Vac (factory setting) or

240 Vac (field change)

• DC motor

• AC powered with integrated battery backup

• 24 Vdc accessory power

• Programmable with up to 50 remote controls, compatible with: Security MAX

codes at either 310, 315, or 390 MHz

• Manual - Secure power failure selection

• SAMS compatible

• Slow-start and slow-stop gate motion

• Reset Button

• Audible Alarm

• Internal Heater option (factory installed or field installed) 120 Vac powered ONLY

• Non-Scissor Action swing arm with easy arm disconnect

• Integrated internal antenna with external antenna option

• Electronic Limit adjustment and control

• Adjustable reversal force

• Adjustable Timer-to-Close (TTC)

• Maximum Run Timer

• Bipart Delay switch (dual gate applications)

• Feedback and Diagnostic LEDs

• Integrated Radio Receiver, Single Button Control (SBC) and 3-Button Station

control, three radio frequencies supporting Security MAX

• COMMANDS:

- OPEN, CLOSE, or STOP: accessory connection and on-board button

- Single Button Close (SBC): accessory connection

- FIRE DEPARTMENT OPEN: accessory connection

- INTEGRATED RADIO RECEIVER:

• LOOPS:

- EXIT, SHADOW, or INTERRUPT LOOP: plug-in loop detector (Model SPI) and

accessory connection

• Plug-in Loop Detector Connectors (Model LOOPDETLM Loop Detector)

- SHADOW

- INTERRUPT

- EXIT, with Fail Safe/Fail Secure selection

• Quick-Close ON/OFF selection switch

• AC Fail Open/Battery selection switch

• Low Battery Open/Close selection switch

• Anti-Tail ON/OFF selection switch

• Single Button Control (SBC) accessory connection

• 3-Button station accessory connection

• AUX Relays (2) each independently selectable operation:

- OPEN LIMIT: ON at open limit switch

- CLOSE LIMIT: ON at close limit switch

- GATE MOVING: ON with gate moving

- PRE-ALERT DELAY: ON 3 seconds before gate motion

- TAMPER: ON when gate manually pulled from close limit

- POWER: ON with AC or Solar power available

- CYCLE QUANTITY: LEDs blink operational cycle count

Summary of content (7 pages)

PAGE 1
INTRODUCTION FEATURES FEATURES OPERATOR FEATURES • Advanced "Centerpiece" Control Board • EMI AC Power Surge Protection and Filter Board - Main AC voltage input selection: 120 Vac (factory setting) or 240 Vac (field change) • DC motor • AC powered with integrated battery backup • 24 Vdc accessory power • Programmable with up to 50 remote controls, compatible with: Security MAX codes at either 310, 315, or 390 MHz • Manual - Secure power failure selection • • • • • • • SAMS compatible Slow-start and slo
PAGE 2
PREPARATION SITE PREPARATION Check the national and local building codes BEFORE installation. CONDUIT & CONCRETE PAD GATE Gate must be constructed and installed according to ASTM F2200 standards (refer to page 4). Gate must fit specifications of operator (refer to specifications). Conduit must be UL approved for low and high voltage. Consider the operator placement BEFORE installing the pad or post.
PAGE 3
SITE PREPARATION SAFETY TYPES OF INSTALLATIONS Entrapment protection devices are required to protect against any entrapment or safety conditions encountered in your gate application (refer to page 5 for more details). Install warning signs on both sides of the gate. STANDARD INSTALLATION (Inside Property) ! ! The illustration is an example of a standard installation.
PAGE 4
INSTALLATION STANDARD INSTALLATION ONLY STANDARD INSTALLATION ONLY MOUNTING FOOTPRINT For compact installation start on page 14. DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR Subtract 12-16 inches from A to get B, the distance from the center of the output shaft to the center of the gate hinge. 3 Open the gate 90°. The distance from the gate to the center of the output shaft must be a minimum of 9 inches. 1/4 1/4 12.2" 6.1" 11" DO NOT run the operator until instructed.
PAGE 5
INSTALLATION STANDARD INSTALLATION ONLY STANDARD INSTALLATION ONLY POSITION THE GATE BRACKET NOTE: It may be necessary to attach horizontal reinforcement to the gate before attaching the gate bracket. Position the operator arm onto the output shaft so that the pin slides into the slot. 1 2 Measure 1/4 the length of the gate from the hinge center. 3 Make sure the operator arm is level and tack weld the gate bracket in this position.
PAGE 6
INSTALLATION COMPACT INSTALLATION ONLY COMPACT INSTALLATION ONLY DETERMINE LOCATION FOR CONCRETE PAD AND OPERATOR TOP VIEW OF OPERATOR AND GATE Gate Hinge Center DO NOT run the operator until instructed. Refer to the illustration to determine the measurements and location of the concrete pad. NOTE: When lifting the operator use the handle to avoid damaging the operator.
PAGE 7
INSTALLATION COMPACT INSTALLATION ONLY COMPACT INSTALLATION ONLY SHORTEN THE OPERATOR ARM For a compact installation the operator arm will have to be shortened. Take the operator arm apart and remove the inner sleeves from the outer tubing. 1 1 2 3 Cut the outer tubing of the operator arm sections to the lengths shown. Put the arm back together and adjust the arm to the measurements as shown. Use the set screws on the arm to temporarily hold the arm in place while determining the correct measurements.