Manualshelf

User's Manual

ManualsBrandsChamberlain Group ManualsElectronicsCommercial Door Operator
12345678910
29
PROGRAMMING
SINGLE BUTTON REMOTE CONTROL PROGRAMMED AS
A SINGLE BUTTON CONTROL (SBC)
This function programs a remote control as a wireless single
button control. This function will work in the following modes:
In B2 mode, operation is OPEN/STOP/CLOSE/REVERSE/STOP.
In T and TS modes, operation is OPEN/STOP/CLOSE/REVERSE/
STOP and Timer-To-Close start/refresh. NOTE: If Car Dealer
mode is enabled, SBC will be open only stopping at the Open
Mid-Stop.
In FSTS mode, operation is OPEN with Timer-To-Close
start/refresh only, bypassing a programmed Open Mid Stop.
1. Press and release the RADIO button on the logic board
(RADIO LED will light).
2. Press and release the SBC externally wired button or TTC on
the logic board (RADIO LED flashes rapidly and then remains
on solid).
3. Press and hold the remote control button until the RADIO LED
flashes rapidly. The RADIO LED will then remain on solid after
releasing.
4. Press and release the RADIO button on the logic board (RADIO
LED flashes rapidly and then turns off). The programming
mode is exited if no activity is performed within 30 seconds
The MAS and RADIO LED’s will flash briefly to indicate the
RADIO has exited the programming mode for remote controls
and touch code devices. The RADIO will remain in program
mode for another 150 seconds for MyQ
®
devices and then will
completely exit with no activity.
NOTE: Single button remote control is not supported with D1 and
E2 wiring modes. C2 mode will only open and stop while opening.
TO ERASE REMOTE CONTROLS
Press and hold the RADIO button on the logic board until the
RADIO LED flashes rapidly (approximately 5 seconds).
All remote controls will be erased.
Built in 3-channel, Security✚
2.0
TM
radio receiver that allows you
to add as many as 90 remote control devices and as many as 30
touch code devices.
NOTE: The following programming requires a LiftMaster
Monitored Entrapment Protection (LMEP) device.
STANDARD REMOTE CONTROL
1. To enter programming press and release the RADIO button on
the logic board (RADIO LED will light).
2. Press and hold the remote control button until the RADIO LED
flashes rapidly, then release remote control button. The RADIO
LED will then remain on solid after releasing the button. Repeat
to add additional remote control(s).
PROGRAMMING REMOTE CONTROLS
Programming
To prevent possible SEVERE INJURY or DEATH:
• Install a LiftMaster Monitored Entrapment Protection (LMEP)
device.
• NEVER permit children to operate or play with door control
push buttons or remote controls.
• Activate door ONLY when it can be seen clearly, is properly
adjusted and there are no obstructions to door travel.
• ALWAYS keep door in sight until completely closed. NEVER
permit anyone to cross the path of closing door.
SLOT 1
RADIO
SLS
MRT MID T
T
RELAY A
RELAY B
12
3
F
P
TTS
E2
D1
C2
B2
CLS
OLS
MID
REV
STD
SLOT 2
MOTOR
DIRECTION
RADIO
3. Press and release the RADIO button to complete the
programming. The RADIO programming mode will exit if no
activity is performed within 30 seconds. The MAS and RADIO
LED’s will flash briefly to indicate the RADIO has exited the
programming mode for remote controls and touch code
devices. The RADIO will remain in program mode for another
150 seconds for MyQ devices and then will completely exit
with no activity.
NOTICE: To comply with FCC and/or Industry Canada (IC) rules, adjustment or modifications of this
transceiver are prohibited. THERE ARE NO USER SERVICEABLE PARTS. Any changes or modifications
not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment. This device complies with Part 15 of the FCC rules and IC RSS-210. Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause undesired
operation. This Class B digital apparatus complies with Canadian ICES-003.