myQ ® Business™ Smart Video Intercom M Model CAPXM INSTALLATION MANUAL 1
Safety Safety Symbol and Signal Word Review When you see these Safety Symbols and Signal Words on the following pages, they will alert you to the possibility of serious injury or death if you do not comply with the warnings that accompany them. The hazard may come from something mechanical or from electric shock. Read the warnings carefully.
INTRODUCTION PRE-INSTALL INSTALL INTRODUCTION INTRODUCTION PRE-INSTALL INSTALL CAPXM Overview........................................................... 4 Control Board Overview................................................. 5 Door Board Overview..................................................... 6 Carton Inventory............................................................ 7 Tools Needed................................................................. 7 Dimensions..................................
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL NETWORK ACCESS CONTROL INSTALL NETWORK ACCESS CONTROL INSTALL NETWORK INSTALL NETWORK CAPXM Overview Smart Video Intercom M (Model CAPXM) is a cloud based access control solution INTRODUCTION PRE-INSTALL INSTALL that includes an integrated video camera enabling advanced video features.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL INSTALL NETWORK ACCESS CONTROL Control Board Overview INTRODUCTION PRE-INSTALL Switches and Diagnostic LEDs Microphone Speaker INTRODUCTION FRONT VIEW PRE-INSTALL INSTALL NETWORK + 3.4 Volts Admin Mode INTRODUCTION PRE-INSTALL + Voltage + 12 Input Volts INSTALL Not Used +5 Volts ACCESS CONTROL BACK VIEW Touch Panel + 3.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Door Board Overview INTRODUCTION INSTALL NETWORK CONTROL The CAPXM has a combinationPRE-INSTALL of access control inputs/outputs on the Door Board that work in conjunction to ACCESS control up to 2 access points.
INTRODUCTION PRE-INSTALL INSTALL NETWORK Ferrite Core ACCESS CONTROL ® Radio Antenna (Security+ 2.
INTRODUCTION PRE-INSTALL INSTALL NETWORK PRE-INSTALL SIDE VIEW INSTALL NETWORK INSTALL 1-1/4" Conduit Knockout NETWORK ACCESS CONTROL Dimensions FRONT VIEW INTRODUCTION 6-1/8 in (15.6 cm) INTRODUCTION PRE-INSTALL 4 in (10.2 cm) BACK VIEW ACCESS CONTROL 2.25 in (5.7 cm) ACCESS CONTROL 15 in (38.1 cm) 17 in (43.2 cm) INTRODUCTION BOTTOM VIEW INTRODUCTION 8.43 in PRE-INSTALL INSTALL NETWORK (21.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Wire Specifications Use this chart to pull wires in preparation of your installation. Check the national and local building codes BEFORE installation. INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL DESCRIPTION OF WIRE RUN WIRE SPECIFICATION MAXIMUM RUN DISTANCE Power Wire, secondary DC output Local Area Network (LAN) INTRODUCTION PRE-INSTALL CAT 5e or better Network Cable.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL NETWORK ACCESS CONTROL Internet Requirements When selecting a router, use the information below to ensure INSTALL compatibility. INTRODUCTION PRE-INSTALL MODEL: CAPXM - Smart Video Intercom M CAPXM can be connected to a router via a wired connection or Wi-Fi. LiftMaster recommends a minimum upload/download speed of 5Mbps for each CAPXM supporting video camera feeds.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL NETWORK ACCESS CONTROL The following services are required for CAPXM to fully function Setup a myQ® Business™ Account INTRODUCTION PRE-INSTALL INSTALL NOTE: If you have an existing myQ® account, your myQ® Business™ account will have the same password. Go to: myQBusiness.com and login. 1. If you do not have a myQ® Business™ account, call LiftMaster Customer Care at 800.323.2276 to activate a myQ® Business™ account.
INTRODUCTION 1 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Remove Knockouts 1. Prepare the work surface by laying down a cloth or To prevent damage to the CAPXM fromACCESS moisture or water: PRE-INSTALL INSTALL NETWORK CONTROL other protective material. • DO NOT install during rain. Internal components MUST be kept from of water and moisture. 2. Lay the CAPXM face down on the protective • BEFORE opening the front cover of the CAPXM, remove ANY material.
INTRODUCTION 2 PRE-INSTALL INSTALL NETWORK Mount CAPXM ACCESS CONTROL DO Make sure the CAPXM is properly sealed to 1. Attach the goose-neck gasket (provided) if mounting to a goose-neck. prevent damage to the CAPXM from moisture. INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL 2. Mount the CAPXM securely to a flat surface or pedestal with appropriate (1/4 in.) hardware taking care to route wiring through appropriate knockouts. Stainless steel hardware is recommended to mount the CAPXM.
INTRODUCTION 3 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Install the Ground IMPORTANT: An earth ground rod is strongly recommended To AVOID damaging gas, CONTROL power or INTRODUCTION PRE-INSTALL INSTALLand should be no NETWORK ACCESS further than 12 feet (3.7 m) from the CAPXM and use a minimum of 12 gauge other underground utility lines, contact underground utility locating wire in most cases. The type and length of earth ground rods vary by region. companies BEFORE digging.
INTRODUCTION 4 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Connect Power The outlet for the CAPXM MUST be an external dedicated 120 Vac outlet. INTRODUCTION PRE-INSTALL INSTALL Refer to the table below for maximum wire run distances. This outlet should be wired back to its own 10 Amp minimum circuit breaker. • DO NOT use ANY power supply other NETWORK ACCESS CONTROL than those supplied with your CAPXM.
INTRODUCTION 1 PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Connect Internet The CAPXM can connect to the Internet with a wired connection or with Wi-Fi® (wireless). See page 10 for Internet requirements. Make sure you are in the Admin Mode before you connect to the Internet. If you are not in Admin Mode, flip switch #1 to the ON position on the Control Board, press the Network tab on the CAPXM display, and INTRODUCTION PRE-INSTALL ACCESS CONTROL press the “Change Network Settings” button.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Gate Access (Wired) Disconnect power BEFORE making electrical connections. Below is an example of a wiring setup for gate access. Gate access can be wired to Door 1 or 2 on the Door Board. LiftMaster® Security+ 2.0® gate operators can also be programmed to communicate wirelessly instead of using a wired connection (refer to the following page). WIEGAND KEYPAD (Not applicable for wireless gate operator connections.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Gate Access (Wireless) The CAPXM can communicate wirelessly to LiftMaster® UL325 gate operators to send open commands, monitor gate position, and send email notifications if an error occurs in the operator (email notifications are configured in myQ® Business™). Up to 4 gate operators can be paired with the CAPXM - one for each primary and auxiliary relay. If using dual gates, program the CAPXM to the primary operator.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Door Access Disconnect power BEFORE making electrical connections. Below is an example of a wiring setup for door access. Door access can be wired to Door 1 or 2 on the Door Board. WIEGAND KEYPAD NOTE: The length of the unshielded wires should be kept to a minimum to avoid electrical noise.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL LiftMaster LMSC1000 RFID Reader Wiring Diagram Arming Loop Detector (Optional) Set Switch #5 to “ON” to enable.
INTRODUCTION PRE-INSTALL INSTALL NETWORK ACCESS CONTROL Wiegand Output Disconnect power BEFORE making electrical connections. The CAPXM offers a Wiegand output capable of 26-bit transmission of the following data: • Success Call with access granted by the resident. The CAPXM will provide a myQ® Business™ specified facility code followed by the Directory Code of the resident that granted access. And/Or • Successful access through Entry Code.
