CHALLENGE 3.6V CORDLESS SCREWDRIVER SS20CSDRI Original Instruction Manual After Sales Support UK/Ireland 0345 640 0800 Important - Please read these instructions fully before starting assembly These instructions contain important information that will help you get the best from your screwdriver, ensuring it remains safe to operate.
Contents Safety Information...................................................................................................... 3 In The Box ...................................................................................................................7 Accessories.................................................................................................................8 Operating Instructions................................................................................................
Safety Information Important - Please read these instructions fully before starting assembly Warning Symbols The following warning symbols appear throughout this assembly manual and indicate the appropriate safety measures you should take when assembling and operating the power tool.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Safety Information Important - Please read these instructions fully before starting assembly General Power Tool Safety Warnings d) Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. e) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. f) Dress properly. Do not wear loose clothing or jewellery.
Safety Information Important - Please read these instructions fully before starting assembly Screw Driver Safety Warning 1. Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock. a) Do not dismantle, open or shred cells or power tool. b) Do not expose power tool to heat or fire.
Safety Information Important - Please read these instructions fully before starting assembly Additional Safety Instructions For Your Battery Charger 15. When charging batteries, ensure that the battery charger is in a well-ventilated area and away from inflammable materials. Batteries can get hot during charging. Do not overcharge any batteries. Ensure that batteries and chargers are not left unsupervised during charging. 16. Do not recharge non-rechargeable batteries, as they can overheat and break. 17.
Accessories 50MM PH2 BITS 50MM SL6 BITS CHARGER 1 1 1 Operating Instructions NOTE: Before using the tool, read the instruction book carefully. Intended Use This tool is intended for driving in and loosening screws. 1. CHARGING THE BATTERY A) BEFORE OPERATING NOTE: a) Do not use any charger other than that specifically provided for use with the equipment. b) If the power tool is very hot you must remove your power tool from the charger and allow time for the battery to cool down before recharging.
Operating Instructions WARNING: Do not suggest to use screw bit shorter than 25mm. When insert into the bit holder, it is difficult to pull it out. 2. FORWARD/REVERSE SWITCH For drilling and screw driving use forward rotation marked “ ” (Forward/Reverse switch (3) is moved to the left). Only use reverse rotation marked “ ” (Forward/ Reverse switch (3) is moved to the right) to remove screws . WARNING: Never change the direction of rotation when the chuck is rotating. Wait until it has stopped! 3.
Trouble Shooting Problem Possible cause Solution Battery will not charge 1. Charger not plugged into a working outlet. 2. Surrounding air temperature is too hot or too cold. 1. Plug charger into a working outlet. Check current by plugging in a lamp. 2. Move charger to an appropriate place which temperature is suitable for the charger. Switch cannot be pressed Forward/Reverse switch at middle position Make sure switch is on Forward or Reverse rotation according to project need.
Technical Data Noise Information A weighted sound pressure A weighted sound power LpA : 73.6dB(A) LwA : 84.6dB(A) KpA & KwA= 3.0dB(A) 80dB(A) Wear ear protection Vibration Information Vibration total values (triax vector sum) determined according to EN 62841 Typical weighted vibration Vibration emission value ah, D = 2.141m/s² Uncertainty K = 1.5m/s² The declared vibration total value may be used for comparing one tool with another, and may also be used in a preliminary assessment of exposure.
Environmental Protection Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. Guarantee This product is selected for DOMESTIC USE ONLY and not for business use. This product is guaranteed against manufacturing defects for a period of 24 months.
