CV SLIDE AND HIDE MULTIPLAY Assembly & User Instructions - Please keep for future reference 745/5744 Important Age Limit: 3-8 years. Max user weight: 45kg Total user weight must not exceed: 225 kg Max user: - Swing (1) per seat - Canopy mat (2) - Slide (1) Tips: It will take 2 adults around 90 minutes to assemble. Important - Please read these instructions fully before assembly or use.
Contents BEFORE YOU START TO ASSEMBLE • Check the package and make sure you have all of the parts listed in the part list section of this user manual. IF ANY PARTS ARE MISSING, please call the Customer Service toll-free number listed on the cover page for assistance. • Do not install or use the product if any parts are missing or damaged. Store in a safe place until ready to install. • Make sure that you have plenty of space and a clean dry area suitable for the assembly of this product.
Warning Important –Please read these instructions fully before assembly or use. WARNING READ ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS EQUIPMENT ● This unit is designed for use by up to 6 children at one time, with maximum weight of 45kg per child and combined weight not exceeding 225kg. ● Assembly requires two adults. ● Children must not use the equipment until it is properly assembled and anchored. Adult supervision is required during the use of this equipment at all times.
Part List If you have damaged or missing parts, call the Customer Helpline: (+44) 0330 0904 420 Please Check you have all the parts listed below 1 Top Right Beam x 1 2 Top Left Beam x 1 3 Upper Tube x 6 4 Canopy Tube x 4 5 Lower Tube x 2 6 Cross Bar x 1 7 Front Mat Rail x 1 8 Rear Mat Rail x 1 9 Side Mat Rail x 2 10 Front Connection Tube x 1 11 Side Connection Tubex 2 10A Rear Connection Tube x 1 12 Front Leg x 1 12A Rear Leg x 1 13 Side Leg x 2 4 14 “U” Shaped bar x 1 15 Canopy x 1 16
Hardware List If you have damaged or missing parts, call the Customer Helpline: (+44) 0330 0904 420 Please Check you have all the parts fittings listed below Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings may be supplied than are required. A B C ×4 (M8×115mm) ×10 (M8×50mm) ×1 (M8×61mm) D E F ×2 (M8×53mm) ×8 (M6×65mm) ×8 (M6×70mm) G H I ×10 (M6×35mm) ×6 (M6×50mm) ×4 (M5×16mm) J K L ×58 (Ø6.5×Ø16mm) ×34 (Ø6.5×Ø10.7mm) ×40 (Ø8.
Part List for Slide If you have damaged or missing parts, call the Customer Helpline: (+44) 0330 0904 420 Please Check you have all the parts fittings listed below Part list for Slide (Part NO. 17) H1 Plastic panel x 1 H2 Plastic panel x 1 H3 Plastic sheet x 1 H4 Support panel x 2 H5 Connecting plate x 1 H6 Connecting plate x 1 H7 Connecting plate x 1 H8 Handle bar x 1 H8A Handle bar x 1 Note: The quantities below are the correct amount to complete the assembly.
Assembly Instructions Step 1 Connect and secure all connection points shown using B, L, M and Q. DO NOT FULLY TIGHTEN THE BOLTS UNTIL THE ENTIRE FRAME IS ASSEMBLED IN STEP 5.
Assembly Instructions Step 2 Connect (10), (10A) and (11) to Canopy Tube (4) as shown. DO NOT FULLY TIGHTEN THE BOLTS UNTIL THE ENTIRE FRAME IS ASSEMBLED IN STEP 5.
Assembly Instructions Step 3 IN THIS STEP, YOU WILL NEED TO INSERT STEEL TUBES INTO THE MAT AND CONNECT THEM TO THE FRAME. ASSEMBLE IN THE FOLLOWING ORDER: 1. Insert (7) through the side of mat with 2 openings (this side will be used for installation of the slide later). Attach (7) to (4) using F, J ,K and P. IMPORTANT NOTES: - The buckles on the mat should be on the bottom side - The indented hole on the steel tubes needs to face up 8 9 7 4 4 4 2.
Assembly Instructions Step 4 - Attach (14) to (7) using G, J, K and P as shown G - Connect (12) to (14) using H13, J, K and P as shown 7 - Connect (12) to (10) using H, J, K and P as shown DO NOT FULLY TIGHTEN THE BOLTS UNTIL THE ENTIRE FRAME IS ASSEMBLED IN STEP 5.
Assembly Instructions Step 5 - Connect (13) to (9) on both sides using G, J, K and P as shown. G - Connect (12A) to (8) using G, J, K and P as shown J K P - Connect (13) to (11) on both sides using H, J, K and P as shown. Please note (13) need to be placed on the outer side of (11). 8 9 9 - Connect (12A) to (11A) using H, J, K and P as shown. Please note 12A needs to be connected to the inner side of 11A. 12A 13 13 NOW CHECK ALL CONNECTION POINTS AND TIGHTEN ALL BOLTS INSTALLED.
Assembly Instructions Step 6 Install the canopy (15) over the assembled platform as shown. Connect the buckles on the canopy to buckles on the bottom of the mat to hold it securely in place. 15 2 Wrap the Velcro straps inside the canopy to the four support legs.
Assembly Instructions Step 7 Attach the basketball net (21) to the hoop, then connect the hoop to the basketball board (19) together with Top Right Beam (1) on the back. Secure with R, O and I as shown in the large diagram.
Assembly Instructions Step 8 Assemble the swing side in the following order: - Insert (5) into (3) and secure together with (6) on the outer side of swing using D, N, L, M and Q. Make sure to attach Plastic Cap (S) onto rail (6) first. - Attach the assembled support legs to (1) using B, L, M and Q. Q L M B L X U - Insert (1) into (2).
Assembly Instructions Step 9 - Connect (1) and (2) and secure with C, L, M and Q as shown in Diagram A. U U - Connect the swing (16) to (1) using A, L, M and Q as shown in Diagram B.
Assembly Instructions Step 10 ASSEMBLY INSTRUCTION FOR SLIDE Place (H3) over (H1) and (H2) as shown. The end of plastic sheet with teeth needs to be placed on the end tilting upward. Make sure the holes on the sides of (H1) and (H2) are facing outward. H3 H2 Connect all 14 points shown in the circles using (H9) and (H12).
Assembly Instructions Step 11 Two people needed for this step. H1 Turn slide over. Slide H7 into the end of plastic sheet with teeth. Tip: gently push the plastic sheet upward with one hand, line up the teeth with the corresponding indents on the bottom of H7 and push it gently to slide it into place. H3 H2 H7 With one person holding H7 firmly in place, another person should insert H4 into the slots at the bottom of H7. Tip: it is easier to install H4 by tilting H7 upwards.
Assembly Instructions Step 12 Secure H4 to the bottom of the slide with H5 and H6 using H10 and H11.
Assembly Instructions Step 13 H8A Insert H8 into H2 and H8A into H1. Holes should be facing outward. Secure using H9 and H12 on both sides. H8 H1 H3 Secure H8 and H8A to H7 using H13 and H14 on both sides.
Assembly Instructions Step 14 Attach the slide to the canopy frame by connecting H8 and H8A to 14 using H, J, K and P. Now check all connection points and fully tighten all bolts installed.
Assembly Instructions Step 15 Anchor the equipment to the ground as shown. Point the anchors at a 45 degree angle and use a hammer to insert fully into the ground. 22 22 22 22 22 WARNING! BEFORE USE, please check all parts and hardware are correctly fitted and secure. If you have any questions, please contact the Customer Help Line (+44) 0330 0904 420.
Assembly Instructions SWING SEAT ADJUSTMENT GUIDE THE LENGTH OF THE ROPE IS ADJUSTABLE TO ACCOMODATE THE HEIGHT OF THE CHILD. TO ADJUST, LOOSEN THE KNOT ON THE SEAT CONNECTOR, PULL ROPE THROUGH THE HOLE TO THE APPROPRIATE LENGTH AND RE-TIE THE KNOT AGAIN. MAKE SURE THAT THE KNOTS ARE TIGHT AND THAT BOTH ROPES ARE ADJUSTED EVENLY SO THAT THE SEAT IS HORIZONTAL.
Care and Maintenance General This multiplay requirement was designed and manufactured with quality materials and craftsmanship. If correct care and maintenance is provided, it will provide users with longer period of exercise, fun and enjoyment. Inspect regularly for: • C H E C K A L L N U T S A N D B O LT S T W I C E MONTHLY DURING THE USAGE SEASON FOR TIGHTNESS AND TIGHTEN AS REQUIRED. IT IS PARTICULARLY IMPORTANT THAT THIS PROCEDURE BE FOLLOWED AT THE BEGINNING OF EACH SEASON.
