MEC-DIS-M002 Mini PCI-e DVI/VGA output graphic board User’s Manual Third Edition, February 2014 © 2014 Cervoz Co., Ltd. All rights reserved.
Mini PCI-e Graphic Card User’s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement. Copyright Notice © 2014 Cervoz Co., Ltd. All rights reserved. Reproduction without permission is prohibited. Trademarks Cervoz is a registered trademark of Cervoz Co., Ltd. All other trademarks or registered marks in this manual belong to their respective manufacturers.
Table of Contents Introduction 4 Overviews 4 Features 4 Installation Flowchart 5 Package Checklist 5 Chapter 2 Hardware Installation 6 Chapter 3 Software Installation 12 Chapter 4 Troubleshooting 21 Appendix Pin Assignments 22 Chapter 1 Board Side Pin Assignments 23 Device Side Pin Assignments 23 Technical Reference 24 MEC-DIS-M002 Specifications 24 MEC-DIS-M002 Dimensions 25 MEC-DIS-M002 Daughter Board Dimensions 25 Product Warranty Statement 26 3
1 Introduction Overview MEC-DIS-M002 is a graphic card for embedded PC. The card follows the Mini PCI-e standard which is complaint with PCI Express x 1 classification and small form factor (30.00 x 50.95 mm). This board fits in any host computer that has Mini PCI-e card slots. Features The PCI Express boards have the following outstanding features: Single-Lane (x1) PCI-Express with throughput up to 2.
Installation Flowchart Installation Flowchart of MEC-DIS-M002 The following flowchart provides a brief summary of the procedure you should follow to install the Mini PCI-e card: Connect the internal cable Hardware Installation Install the card in the Mini PCI-e slot Hardware Installation Connector Fixation Hardware Installation Install the driver Software Installation Package Checklist The following items are included in the Mini PCI Express board Package: Mini PCI-e Card x 1 Daughter board
2 Hardware Installation This chapter describes the PCI Express Series hardware installation procedure. Since the BIOS automatically assign the PCI Express board’s IRQ number and I/O addresses, you must plug in the board before installing the driver.
Step 2 Install the card to the Mini PCI-e slot Make sure you install the card in the right position (fool-proof design) Step 3 Fix the card on the motherboard (clip type or screw type) There are 2 options to fix the card. It depends on the design of the motherboard (clip or screw). 1. Clip type: make sure you press down the card and let the clips fix the card 2.
Step 4 Card installation completed Find any place on mother board that you can screw the ground cable. Step 5 Connect the cable to the daughter board 1. Connect other side of the cable to the daughter board 2. Connect the ground cable on daughter board or chassis or mother board where you can screw it. 1. Both sides of the cable connectors are the same, it doesn’t matter which Note side you connect 2.
Connector Fixation MECFIX – Versatile Mounting 1. Standard PCI/PCIe Bracket PCI / PCIe IO Bracket 2.
3.
4.
3 Software Installation This chapter gives installation, configuration, and update/removal procedures for the driver for Win 2003, Win XP, Win Vista, Win 7, and Win 8.
Step 2 1. Windows automatically detects the new device If the card is installed properly, system would detect the new device and the hardware wizard would start automatically. 2.
Step 4 Find the “MEC-DIS-M002” folder Open the “MEC-DIS-M002” file folder Step 5 Find the “Driver” folder Open the “Driver” folder 14
Step 6 Find the appointed OS folder (Ex.: XP) Open the appointed OS folder (We use XP as an example in the above picture) Make sure you select the correct OS Step 7 Find your OS version (Ex.: XP 32bit) Select appoint OS folder (We use XP 32bit as an example in the above picture) Make sure you select the correct version of the OS (Ex.
Step 8 Find the “setup” file Run the “set up” file Step 9 Driver installation set up Click “Next” 16
Step 10 Select destination location 1. Select the location where the driver will be installed 2. Click “Next” Note If you are not sure what location to be installed, keep the default setting and click “Next”.
Step 11 Select Start Menu folder 1. Select the start menu folder 2. Click “Next” Note Step 12 Note: If you are not sure what folder to be selected, keep the default setting and click “Next”.
Step 13 Installation in progress Step 14 Disregard logo testing 1. Before installation is completed, logo testing window would pop out. Disregard this information and continue the installation progress 2.
Step 15 Driver installation completed, restart PC 1. Select “Yes, restart the computer now” 2. Click “Finish” Step 16 Confirm if driver is installed 1. When you restart Windows, you would find the SMI icon on the right bottom corner 2. Start “Computer Management” program 3. Go to the route: My Computer → Manage → Device Manager → Display adapters 4. You would find the driver name: Silicon Motion SM718/SM750 5.
4 Troubleshooting If MEC-DIS-M002 is removed from motherboard, a warning window would pop out stating “No SMI graphics driver to support the control panel!” No 1 Causes Solutions Once MEC-DIS-100 is removed from 1. Remove the driver motherboard, the driver is not able to Route: Control Panel → Add or find the SMI chip.
Appendix Pin Assignments 22
Board Side Pin Assignments Wire to Board Connector (CN10、CN11) Pin Description Pin Description 1 TD0+ 11 DDC_CLK 2 TD0- 12 +5V 3 TD1+ 13 CRT_Red 4 TD1- 14 CRT_Green 5 TD2+ 15 CRT_Blue 6 TD2- 16 CRT_HSYNC 7 TC+ 17 CRT_VSYNC 8 TC- 18 DDC_SDA 9 DVI_DHP (Hot Plug) 19 DDC_SCL 10 DDC_DAT 20 GND Device Side Pin Assignments DVI-I Port Female Connector (DVI_I1) Pin Description Pin Description Pin Description 1 TD2- 9 TD1- 17 TD0- 2 TD2+ 10 TD1+ 18 TD0+ 3
Technical Reference MEC-DIS-M002 Specifications General PCI-Express Revision PCI-Express Electromechanical Revision Hardware Controllers Bus Interface (Connector) PCI-Express Base Specification Rev 1.1 PCI-Express Mini Card Electromechanical Rev. 1.1 SiliconMotion SM750 with 16MB DDR SDRAM Single-Lane (x1) PCI-Express with throughput up to 2.
MEC-DIS-M002 Dimensions MEC-DIS-M002 Dimensions 25
Product Warranty Statement Cervoz products are warranted to be free from manufacturing defects in materials and workmanship starting from the date of delivery. The actual warranty period of Cervoz products vary with product categories. Complete details can be found here: http://www.cervoz.com/support/warranty.php During the warranty period, we shall, at our option, either repair or replace any product that proves to be defective under normal operation.
