Owner's Manual

MID-16
MID-16 Programmable Input Driver
The MID-16 is an input module used in conjunction with
the MOI-7 as a part of the Cerberus Pyrotronics MXL
System. Up to eight MID-16s can be connected to a single
MOI-7 along with eight MOD-16 output driver modules.
Each MID-16 provides a non-supervised input which can
monitor contact devices. Each individual MID-16 input can
be separately used as a part of the MXL custom program-
ming logic. These inputs can be individually set for either
Alarm, Supervisory, Trouble, Security or Status usage. They
can also be configured to provide supervision for lamps
driven by MOD-16 outputs. Screw terminals and connec-
tors are provided on the MID-16 modules for interface to
monitored devices.
MOD-16
open collector current sinking outputs rated at 24 VDC,
50mA. MOD-16 outputs are programmable through the
MXL custom software.
MME-3
MBR-MP MME-3 and MLE-6 MXL Module Mounting
Plate
The MBR-MP MXL/V Module Mounting Plate is required for
use in both MME-3 and MLE-6 enclosures to mount all MXL
and MXLV equipment. MBR-MP is not necessary if the
MME-3 and MLE-6 enclosures are to be used only for
mounting of amplifiers (EL-410).
The MBR-MP is a removeable MXL/V module mouting plate
that allows the enclosure MME-3 or MLE-6 to be shipped to
the job site for installation of wiring and conduit, while the
system hardware (electronics) is mounted to the studs on
the MBR-MP, pre-wired, programmed and tested prior to
delivery and installation at the job site. This allows for
quicker, more efficient system start ups with less chance of
the sensitive electronics being damaged while field wiring
and conduit are connected to the system enclosure.
MBR-MP mounting plate bolts to either the MME-3 or MLE-
6 enclosures for easy installation on the job site. The MBR-
MP also has handles to allow easy transport and mounting.
The MBR-MP contains mounting studs for (1) MMB or PSR-
1, (1) PIM-1, (1) TBM-1, and up to (3) MOM or OMM
cardcages or 2 cardcages and (1) TSP-40 Printer (same
mounting studs as the MBR-2 enclosures).
The MBR-MP is ordered and shipped seperately from the
MME-3 and MLE-6 enclosures.
MME-3 MXL/V Standard Size Enclosure
The MME-3 enclosure set consists of a sheetmetal backbox
and
door with keylock. The MME-3 can be used for either
the MXL System, MXLV Voice Command Console, MXLR
Transponder, MXLRV Voice Transponder or Amplifier
Equipment (using the MSR-1 Rail Kit). To mount MXL/MXLV
modules in the MME-3, the MBR-MP removeable module
mounting plate is required. Using the MBR-MP mounting
plate (1) MMB or (1) PSR-1 and up to 3 expansion
cardcages (MOM or OMM) can be mounted in the MME-3
enclosure. When used to mount MXL amplifiers (EL-410),
the MBR-MP is not required, instead up to (3) EL-410
amplifiers may be installed in the MME-3 by using (3) MSR-
1 rail kits. When amplifiers are mounted in any enclosure
always install MDG-1 grills in the door for proper ventilation.
MME-3 is designed for surface of semi-flush mounting and
includes various knockouts for wire and conduit entry. The
door in the MME-3 set has two cutouts for either clear
lenses, blank plates or grills depending on the application,
and contains a key lock.
MBR-MP
MLE-6 MXL/V Large Size Enclosure
The MLE-6 enclosure set consists of a sheetmetal backbox
and door with two key locks. The MLE-6 can be used for
either the MXL system, MXLV Voice Command Console,
MXLR Transponder, MXLRV Voice Transponder or Amplifier
Equipment (using the MSR-1 rail kit). To mount MXL/V
modules in the MLE-6, the MBR-MP removeable module
firealarmresources.com