CT-Multi-PTT Bluetooth Operation Instructions English- USA - Canada Revision: 02/1015 DOK 1643-us
Contents 1 Warning - and Safety instructions ................................................................... 3 1.1 2 3 4 5 General safety instructions....................................................................................................... 3 Abbreviations and Terms................................................................................ 5 Scope of delivery ............................................................................................ 5 Labeling of the product ....
7.18 Switch-on and operation ........................................................................................................ 24 7.18.1 Communication via radio................................................................................................. 24 7.18.2 Communication via cellular phone .................................................................................. 24 7.19 End of operation.................................................................................................
authorized by CeoTronics. In all other cases, our warranty and liability for the product shall lapse. Keep CeoTronics products out of the reach of children and any other persons who are not familiar with the handling and operation thereof. CeoTronics products may only be used for the specific application envisaged. Product damage! Do not immerse a CeoTronics product into water, if it is not expressly specified for this purpose.
Legal note for operation in the USA The receiver of the CT-Multi- PTT should be used in the USA only when it is marked as following: 916,5 MHz Important Notes for operation of the Transmitter in the USA Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment This device complies with Part 15 of the FCC Rules.
Figure 1 – Example metal clip Serial number FCC labeling 5 Product description 5.1 Description The CT-Multi PTT Bluetooth (PTT-Push to talk) provides the possibility of cable connection to a radio and to a cellular phone via the integrated Bluetooth interface. The necessary CT communication set (not part of the scope of supply) is plugged into the corresponding socket.
Figure 2 Example Wearing method max. 40 cm The CT-Multi PTT Bluetooth complies with the Bluetooth specification 2.1. At some places, there exist restrictions regarding the use of Bluetooth devices. Ask your service provider or the competent authorities. An AA battery or AA storage battery provides the electrical power. For radio operation, the Bluetooth module must be in switched-on state, even if no cellular phone is used. Normally, switch-on is controlled via radio or by keystroke.
Figure 3 c a f d g h e i b a b c d e f g h I Plug for connection to a radio Pasted label with name of device Socket for communication set Battery compartment PTT button Bluetooth control button + storage battery / battery pilot lamp Green, continuous - battery fully charged Green, flashing - battery at half charge Red, flashing - battery almost flat, approx.
Figure 4 5.2 Figure 5 Fixation clamp The clamp can be rotated 360 °, infinitely variable.
5.3 CT-Multi-PTT Bluetooth with CT-ClipCom Digital The CT-Multi-PTT Bluetooth is also available with integrated CT-ClipCom Digital technology and firmly attached communication set. The following two (2) system configurations are available: CT-ClipCom Digital EarMike consisting of an ear microphone and an additional speaker You hear radio messages and the ringing tone of the cellular phone on both sides.
Figure 8 a Earphone on the left side b Ear microphone on the right side c Ear microphone with earphone d ASR microphone 5.3.2 Earphone with BoomMike The earphone with boom microphone is available only for the left ear. Attached to the earphone is the boom microphone with protective cover (Figure 9/c) and the ASR microphone (Figure 9/b).
5.3.3 Use with standard ear plug Figure 10 Figure 11 Figure 12 The standard earplug is used for adaptation of the ear microphone / earphone to the auditory canal. It is »pushed« with a rotating motion onto the ear microphone / earphone (Fig.10). If no perfect seat inside the ear is achievable, because the standard earplug is too large, the largest lamella ring can be cut off with a sharp knife (figure 10-12). 6 Preparing the Product for Use 6.
7 Operating Instruction 7.1 7.1.1 Change of the battery Change of the battery – CT-Multi PTT Bluetooth Figure 13 1. Open the battery compartment by loosening the knurled screw. 2. Remove and replace the rechargeable battery / battery from the battery compartment. When inserting observe polarity. 3. Fix the cover of battery compartment again at the PTT-button.
7.1.2 Change of the battery in the CT-Wireless-PTT 1. Open the battery compartment at the back of Figure 15 the CT-Wireless-PTT with help of the special tool by short turn to left. 2. Remove the circuit board careful from the housing. Change the battery and pay attention to the correct position; the lettering must be visible. Use only the 3 V batteries type CR2032. Figure 16 Circuit board Pay attention to the correct polarity.
7.2 Connect the CT-MultiPTT Bluetooth to the radio 7.2.1 12-pin connector Damage to connectors, sockets and/or cables Observe the following instructions when handling plug-in connections. Normally, the 12-pin connector is used in combination with radio adapters. For it, the adapter is attached to the radio and the 12-pin connector itself plugged into the radio adapter. Turn the radio off, if it is turned-on. Plug the 12-pin connector into the radio adapter.
Figure 20 7.3 Switch-on Press simultaneously Bluetooth key and volumeup key until you hear an ascending three-tone sequence in the CT communication set. Then let the buttons go. The LED in the Bluetooth key indicates the condition of the battery/storage battery. Should the LED not illuminate continuous green since the first second of switch-on, then the battery or storage battery is flat, and has to be replaced. Operation is not possible. 7.
Figure 22 7.6 Change operating modes You may switch between telephone mode (mode 1), telephone mode with MIC-switch (mode 2), and limited telephone mode with MIC-switch (mode 3). For it, proceed as follows The modes are signalized by the following beeps: Mode 1- 1 beep cellular phone mode Mode 2- 2 beeps cellular phone mode with MIC-switch Mode 3- 3 beeps limited cellular phone mode with MIC-switch 1.
microphone. The microphone remains switched-on as long as the key is pressed. In the event the existing phone call has been interrupted intentionally or unintentionally, you hear in the CT communication set two times a descending sequence of tones. In the telephone mode with MIC switch, the Bluetooth key serves the following functions: Accept the call End the call Reject the call Redial Abort redialing You can use the CT-Wireless-PTT in lieu of the Bluetooth key; it has equal function. 7.8.
LED flashes green: LED flashes red: at half charge very low – replace You hear in the CT communication set three (3) low beeps in 30-second intervals Undser heavy load and high volume and depending on the battery/storage battery status the communication may result in a distortion-like audio impression. This is normal and prevents system crashes / malfunctions if a battery / storage battery does not provide enough power anymore.
7.14 CT-Wireless-PTT (optional) For interference-free operation of the CT-Wireless-PTT receiver in the CT-Multi PTT Bluetooth, take care that the CT-Multi PTT Bluetooth is not located in close proximity to the transmitting antenna of a radio or cellular phone. Heterodyning the CT-Wireless-PTT radio signal by the comparatively strong transmit signal of a radio or cellular phone can compromise the sensitivity of the CT-Wireless-PTT receiver in the near field of the transmit antenna.
7.15 Subscribe the CT-Wireless-PTT to the CT-Multi PTT Bluetooth Figure 25 1. Switch the CT-Multi PTT Bluetooth off, if it is on. 2. Press all three (3) lateral keys of the CT-Multi PTT Bluetooth simultaneously until the LED of the Bluetooth button starts flashing three (3) times red-green. The LED keeps flashing redgreen until you let the keys go, however minimum three times. 3. Press the Bluetooth key three (3) times until the LED flashes as follows: ….red-red-red…..red-red-red….red-red-red…. 4.
7.16 Delete one CT-Wireless-PTT from the memory of the CT-Bluetooth Adapter Figure 26 1. Switch the CT-Multi PTT Bluetooth off, if it is on. 2. Press all three (3) lateral buttons of the CT-Multi PTT Bluetooth simultaneously until the LED in the Bluetooth button starts flashing three (3) times redgreen. The LED keeps flashing red-green until you let the buttons go, however minimum three times. 3. Press the Bluetooth key of the CT-Multi PTT Bluetooth and hold it down for at least two (2) seconds.
7.17 Delete all CT-Wireless-PTT from the memory of the CT-Bluetooth Adapter Figure 27 1. Switch the CT-Multi PTT Bluetooth off, if it is on. 2. Press all three (3) lateral keys of the CT-Multi PTT Bluetooth simultaneously until the LED in the Bluetooth button starts flashing three (3) times redgreen. The LED keeps flashing red-green until you let the buttons go, however minimum three times. 3. Press the Bluetooth key of the CT-Multi PTT Bluetooth and hold it down for at least two (2) seconds.
7.18 Switch-on and operation Risk of hearing impairment For safety reasons reception volumes in excess of 85 dB(A) are possible with a whole series of CeoTronics products. However, the user can regulate the volumes. After switching on the communication system, set the reception volume to approx. 1/2 the available loudness volume and then test the audible volume, e.g. by opening the squelch on the radio set. Do not set the volume any higher than is necessary.
Should the radio be turned off (battery change) while the Bluetooth module is on, you hear in the communication set for 30 seconds an acoustic warning signal in two (2) second intervals. During these 30 seconds press a key or turn the radio on, to ensure the Bluetooth module continues in switched-on condition. This way it is possible to keep up telephone standby. Switch off the Bluetooth module Turning the radio off, switches the Bluetooth module off as well, with a delay of 30 seconds.
8.1 Cleaning Product damage! Pay attention that no humidity could penetrate into the device during cleaning. Do not use solvents (e.g. benzene, alcohol, etc.) for cleaning! Safe operation requires clean devices. Ensure that the devices (microphones, connectors etc.) are clean and in good condition at all times. Remove loose dust with a soft brush. Clean the outside of components, if necessary, with an appropriate clean cloth, only lightly moistened with clear water, and then rub it down thoroughly.
Revision: 02/1015 DOK 1643-us Brief keying Lautstärke verringern Hold 2 seconds Display operating mode Brief keying Hold 2 seconds Activate wireless configuration Lautstärke erhöhen Hold 3 seconds Abort pairing mode Hold 2 seconds, brief keying Hold 8 seconds Activate pairing mode Change operating mode Hold 3 seconds Switch off Keying duration Hold 3 seconds Key combination Switch on Function Sound signal Descending 3-tone sequence On Off Executable in condition 27 of 28 LED activ
Deutschland und Internationaler Vertrieb CeoTronics AG Adam-Opel-Str. 6 63322 Rödermark Tel. +49 6074 8751-0 Fax +49 6074 8751-676 E-Mail verkauf@ceotronics.com USA/Kanada/Mexico CeoTronics, Inc. 512 South Lynnhaven Road, Suite 104 Virginia Beach, Virginia 23452 Tel. +1 757 549-6220 Fax +1 757 549-6240 E-Mail sales@ceotronicsusa.com Spanien CeoTronics S.L. C/Ciudad de Frias 7 y 9 Nave 19 28021 Madrid Tel. +34 91 4608250 51 Fax +34 91 4603193 E-Mail ventas@ceotronics.
