CT-ClipCom Digital Operating Instructions Example English
Contents 1. Important safety instructions ..............................................................................................................2 2. Description .........................................................................................................................................3 2.1 Ear-microphone ...............................................................................................................................5 2.2 Earphone with gooseneck-microphone ..............
z Do not leave CeoTronics products lying around loose in cars, e.g. on the parcel shelf. Stow these products in a suitable, safe place in the car so that they do not present a danger to you or to other occupants of the car, if emergency braking is effected. z Keep CeoTronics products out of the reach of children and any other persons who are not familiar with the handling and operation thereof. z Packaging materials, e.g.
System overview (examples) figure 1 CT-ClipCom Digital gooseneck microphone figure 2 CT-ClipCom Digital ear-microphone a b c d e f a b c d e f ear-phone earphone with gooseneck microphone connector PTT-button CT-Wireless-PTT (Option) accessories or two-way radio (example, not in scope of delivery) 4 ear-microphone ear-phone connector PTT-button CT-Wireless-PTT (Option) accessories or two-way radio (example, not in scope of delivery)
2.1 Ear-microphone The ear-microphone is at the right side and is identified by a red marking. The earphone is at the left side and is identified by a blue marking. The casing of the ear-microphone contains the optional ASRmicrophone (figure 3/d) in addition to the ear-microphone itself (figure 3/c). For using the earmicrophone it is just clipped onto the individual ear mould (see 2.3). figure 3 a ear-phone left b ear-microphone right c ear-microphone and earphone d ASR-microphone (Option) 2.
2.3 Individually ear mould This ear mould (example Fig. 5) ensures maximum wear comfort and transmission quality. It is moulded according to an individual impression of the auditory canal either for wearing in the right ear or in the left ear. For different personal needs different variants are available. The earphone is “clipped” in the ear mould. The ear mould is worn in the ear.
Removing the earphone from the ear mould figure 8 a. Take the ear mould in one hand and press the two ends of it against each other (figure 8) until ear microphone "disengages" from the ear mould. ATTENTION! Never extract the earphone from the ear mould by pulling the cable. b. Now hold the earphone with the other hand and pull it out of the ear mould. 2.4 Wired PTT-button The PTT transmit button is provided with connecting cable and plug for connection to a radio unit adaptor.
2.4.1 Ambient sound reception (option) The ambient sound reception (ASR) happens via the microphones in the ClipCom earphones. He can be adjusted with the key fig. 9/g of the appropriate situation. The adjustment takes place in 4 steps Initial position: 0dB (normal hearing) 1st keying +6dB nd 2 keying OFF 3rd keying -6dB th 4 keying RESET to 0dB 2.5 CT-Wireless-PTT (option) This transmit button is a radio key to transmit PTT commands to a connected radio device.
2.5.2 Deleting one CT-Wireless-PTT from the memory of a wire-bound PTT transmit button 1. Switch OFF the radio unit connected to the wire-bound PTT transmit button if it is in switched-on state 2. Insert the CT-ClipCom ear microphones/earphones in the ears 3.
Switch the radio or communication device ON and adjust at the radio or communication device the desired volume of reception for the ear microphone. CAUTION! Before each start of operation control the volume of reception and adjust it, if necessary. Very loud signals could damage your hearing. Observe the manufacturer’s operating instruction for the radio and/or communication device. e.
Ear moulds and Earphones Obstructed sound channels of ear moulds and earphones cause poor reception. For regular cleaning (after every use) we recommend the use of special antiseptic cleaning tissues (see item 6), an appropriate cleaning spray, or soft clean cloths and pure water with some dishwashing liquid. Do not use solvents for cleaning purposes. For a basic cleaning of ear moulds we recommend a cleaning bath once a week (effervescent tablets; e.g. Detax Smarttabs). 5.
6. Consumable parts Designation Cleaning tissues Protective microphone cover Unit pack of 100 pack of 10 Part No. 60 98 293 50 022 03 Germany and International Sales CeoTronics AG Adam-Opel-Str. 6 63322 Rödermark Tel. +49 6074 8751-0 Fax +49 6074 8751-676 E-Mail sales@ceotronics.com USA/Canada/Mexico France Spain CeoTronics, Inc. 300 Southport Circle, Suite 103 Virginia Beach, Virginia 23452 Tel. +1 757 549-6220 Fax +1 757 549-6240 E-Mail sales@ceotronicsusa.com CeoTronics Sarl Bât. Delta T Z.A.
