Century Corporation User's Manual HDD Stand Converter Clone Plus CROS2EU2CP User Manual CROS2EU2CP Manual 2010/04/27
【Features】 Part no. : Model name : Interface : CROS2EU2CP HDD Stand Converter Clone Plus Device...SATA I/II 1.5Gbps/3.0Gbps Host ...[USB]USB2.0 [eSATA]SATA II 3.0Gbps Connector : USB TYPE-B Dimension : L143mm x W132mm x H70mm Weight : 544g (HDD not included) Humidity : 20% to 80% Temperature: 5~35°C Power Adapter:Input...100V~240V 0.8A Output...
【Hardware Guide】 〈Front〉 ① HDD dock slot ② HDD release button ③ Operation panel 〈Back〉 ① eSATA port ② USB 2.
〈Operation Panel〉 ① Power Switch: When power on,will show blue light. ② PC / Copy Mode Switch: － PC Mode (Blue light):When CROS2EU2CP connects with PC. - Copy Mode(Red light):When power is on,long press the button for 3 seconds. After the LED turn to RED, can begin copy operation. ③ Start: Press the button to begin copy operation. ④ HDD Status LED: Blue for HDD recognized. Pink flash for access HDD. ⑤ Progress status LED: Copy Mode-25% as a unit to show copy operation progress.
【HDD/SSD Installation】 ■Before insert the HDD Please be careful with the static electricity, when insert the HDD. The static electricity might cause the damage to the HDD stand converter. ※ Warning! Please back up the data of the HDD before connecting. Warning! ■Please be careful withe the order. ・Insert the HDD before turn on the power. ・CROS2EU2CP does not support hot-swap. It may cause damage, if the order is incorrect. Do not remove or insert HDD when power on.
※CROS2EU2CP is for SATA HDD, does not support PATA(IDE) HDD. confirm Warning! SATA Connector PATA Connector ■3.5＂HDD installation Insert the 3.5＂hard drive into the dock slot 〈After〉 ■2.5＂HDD installation Insert the 2.5＂hard drive into the dock slot 〈After〉 ■ Warning！ When install, please notice the correct SATA connector location and direction. If push too hard, it might cause damage.
【HDD/SSD Remove】 ※ CROS2EU2CP does not support hot-swap plug. Please turn off the power before remove. 1.One hand hold on the HDD, and push the button to release the HDD from the dock. Hold on the HDD! Push the release button 2.After pushing, the HDD will eject from the docking. Pull the HDD out vertically. ■ Warning！ Must hold on the HDD when remove, or it may cause damage to the SATA connector.
【Connect with PC】 Connect the PC and power to start! CROS2EU2CP docking USB port eSATA port eSATA cable Cannot work at theできま same time 同時に使用す AC adapter Power cord USB2.0 Cable Plug （100V AC ） ※ Above is an example. Please do not twist the eSATA cable when using.
【Turn on the Power】 Press the button to trun on and turn off the power. Please turn off the power before connect with cable.
【HDD Copy Function】 HDD docking station deliver an exact 1 to 1 , sector by sector disk copy. No need to format the HDD,if there are system files already in the HDD. Warning! ～Before Copy Operation～ Please read the operation manual before start copy operation, there might cause damage to the HDD, if the operation is wrong. When in following situations, might cause the copy operation failed, - Broken sector in HDD - Unrecognized HDD - Others,unstable HDD ■ Operating instruction 1.
2.After confirm the power is off, insert the Source Disk into HDD 2, and insert Target Dick into HDD 1. HDD 2 POWER OFF (SOURCE DISK) CONFIRMED! HDD 1 (TARGET DISK) COPY Warning! Please be careful with the correct solt for the TARGET and SOURCE DISK. It might cause damage to the HDD, if it’s reversed. And the capacity of TARGET DISK should be bigger than SOURCE DISK or the same. If use the same capacity please choose the same brand, otherwise there might be some error between different brands.
3.Press the button to start!(①) Press PC/COPY button for 3 seconds, LED will turn from blue to red（②） � Long press for 3 seconds �POWER ON Blue Turn to red 4.Press START button to start copy operation. When in copy operation,HDD1/HDD2 light will will be blue flash from left to right,25% a Once finished, the Progress Status LED will the HDD1/HDD2 will change from pink to blue be pink flash, and the Progress Status LED unit to indicate the finished copy status.
【Copy Operation-Technical Support】 Following are the reasons might cause the duplication process could not begin or disrupt, ■ Could not begin process One of the HDDs might have broken, or the TARGET HDD is smaller than SOURCE HDD in capacity. Please change a HDD or bigger TARGET HDD. HDD1/HDD2 LED only flashes once pink flash Progress LED is not flshing ■ Process disrupted The process will disrupt if there is erron in one of the HDDS. Please turn off the power and check the HDD.
【FAQ】 Q:Maximum capacity of HDD? A:Support HDD up to 2.0 TB in capacity. Q:Does it support hot-swap? A:No, please turn off the power before insert or remove the HDD. It may cause damage to the HDD, if the power is on. Q:What is the insertion rate of the HDD converter? A:For the HDD stand converter, 10,000 times. For HDD, should consult with the HDD manufacturer. Q:Is the HDD stand converter bootable? A:Through eSATA connector is bootable, but depends on environment.
【FAQ- Copy Mode】 Q:Could it copy HDD in different capacity? A:Yes, but the TARGET HDD should always bigger than SOURCE HDD. Q:Could it use the remain capacity in the HDD after copy operation? A:In the copy mode it will copy all sector in the HDD. For example, the SOURCE HDD is 500GB and the TARGET HDD is 1TB,the 500GB in the TARGET HDD will be exactly the same as the SOURCE HDD. For the remaining 500GB in the TARGET HDD,could use in the Windows XP/Vista/7, but if in Mac OS, it could not be used.
