Operating Instructions and Installation Instructions

ManualsBrandsCenturion ManualsVehicleKS 50

Offertes en leveringen geschieden volgens onze leveringsvoorwaarden gedeponeerd ter Griffie van de Arrondissementsrechtbank te Amsterdam.

Diverse Centurion geautomatiseerde segmentdeuren zijn getest en goedgekeurd voor gebruik bij het Politiekeurmerk Veilig Wonen®

Centurion Deuren B.V.

Kantoor

Koningsweg 2-13, 3762 EC Soest

Werkplaats/Showroom

Nijverheidsweg 24, 3762 ER Soest

(035) 60 30 982

(035) 60 31 544

info@centuriondeuren.nl

www.centuriondeuren.nl

IBAN NL87 RABO 0131 1795 43

KvK 32032777

BTW NL 0051621B02

1394-Centurion Briefpapier.indd 1 04-11-13 10:46

KSA-series KSA-series KSA-series

WNER’S & INSTALLATION

MANUAL

Page 3

Please keep this manual for future reference, repair and maintenance.

NTRODUCTION

Congratulations on the purchase of your new automatic garage door operator. It is designed to

offer you convenience, durability and quality. This operator has been factory tested to ensure

maximum quality and safety.

In order to prevent damage to the garage door or garage door operator and to comply with the

Machinery Directive it is important that this operator is fitted in accordance with these instruc-

tions.

CONTENTS

Gebruikers- & Installatiehandleiding

KSA & KS 50

Summary of content (20 pages)

PAGE 1
CONTENTS Centurion Deuren B.V. Kantoor Koningsweg 2-13, 3762 EC Soest Werkplaats/Showroom Nijverheidsweg 24, 3762 ER Soest T F E I (035) 60 30 982 (035) 60 31 544 info@centuriondeuren.nl www.centuriondeuren.
PAGE 2
 IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION WARNING – INCORRECT INSTALLATION CAN LEAD TO SEVERE INJURY FOLLOW ALL INSTALLATION INSTRUCTIONS Before installing the operator check that the door is in good mechanical condition, and correctly balanced, and that it opens and closes properly. • Do not use the force adjustments to compensate for a binding or sticking garage door. Excessive force will interfere with the proper operation of the Safety Reverse System or damage the garage door.
PAGE 3
Please keep this manual for future reference, repair and maintenance. INTRODUCTION Congratulations on the purchase of your new automatic garage door operator. It is designed to offer you convenience, durability and quality. This operator has been factory tested to ensure maximum quality and safety. In order to prevent damage to the garage door or garage door operator and to comply with the Machinery Directive it is important that this operator is fitted in accordance with these instructions.
PAGE 4
SAFETY FEATURES • Automatic Door Reverse An unmodified closing door will automatically reverse within 2 seconds if door is obstructed by person or object. • Automatic Time Reverse Closing door will automatically reverse if the door is not fully closed within 88 seconds. • Safety Stop Opening door will immediately stop when obstructed by person or object. Beam Break For additional safety we recommend a Beam Break is installed.
PAGE 5
Operator O PERATORassembly ASSEMBLY Note: Where the operator has been specified with a 2-piece boom, please refer to the assembly instructions for this item supplied with the boom.  Install carriage stops into channel (motorhead side).  Install grey motorshaft adapter onto motorshaft Bolt rail with brackets and screws to motorhousing. Make sure the screws are tightly fastened.  Fit the red slider that re-engages the emergency release and operator pull bar onto carriage. Refer to fig.
PAGE 6
 Carriage quick release. a. Pull cord ''a'' to disengage. Carriage re-engage remain disengaged. See fig. 3 b. Move red slider ''b'' in direction of arrow to re-engage carriage at next movement. Start operator. See fig. 4. fig. 3 fig.
PAGE 7
 Install limit clips. a. Make sure the carriage is engaged and in the middle of the rail. b. There are three sets of limit clips included; two sets for belt drive and one set for chain drive c. Install correct limit clips for chain or belt as indicated in illustrations approximately 90cm from carriage between carriage and motorhead. Note: If a chain drive channel is being fitted, then remove the limit clip already attached to the chain and install, together with other clip supplied, as instructed above.
PAGE 8
Operator OPERATORinstallation INSTALLATION DETERMINE GARAGE DOOR TYPE Determine your garage door type as indicated in Step , ,  or . Follow the individual instructions required for your specific garage door type. If your garage door type is not included, please contact your distributor. Special accessories or operator modifications may be required.  1-Piece up-and-over doors min. 35 mm 10 mm       Assemble the door pull arm as shown before fitting the door bracket.
PAGE 9
 Sectional doors min. 35mm 10 mm        ATTENTION Assemble the door pull arm as shown before fitting the door bracket. Make sure the nuts and bolts are fully tightened. A beam break is strongly recommended for use with sectional doors (available separately). - Fix adjustable door fitting bracket to top section at the centre of the door. - Install rail bracket on centre position above door. Make sure there is at least 10mm clearance between highest travel point of door and rail.
PAGE 10
 Retractable non-protruding up-and-over doors min. 35 mm 10 mm Special adapter arm (curved door arm) is required. An optical sensor is strongly recommended (not included; have to be ordered separately).  ATTENTION - Install rail bracket on center position above door. Make sure there will be at least 10 mm. clearance between highest travel point of door and rail. - Fit the adapter arm (curved door arm) according to instructions of adapter arm supplier. - Level and mount operator.
PAGE 11
 Vertically tracked canopy doors min. 35 mm 10 mm  Special adapter arm (curved door arm) is required (not included; have to be ordered separately). ATTENTION - Install rail bracket on center position above door. Make sure there will be at least 10 mm. clearance between highest travel point of door and rail. - Fit the adapter arm (curved door arm) according to instructions of adapter arm supplier. - Level and mount operator.
PAGE 12
FOR  ALL OTHER DOOR TYPES PLEASE CONTACT YOUR DISTRIBUTOR! Make sure motorhousing and rail are mounted correctly and secured. Strengthen where needed.  Attention: Before you start Operator programming please make sure your carriage is engaged to chain or belt and door arm is attached to door.  Install light bulb. Type E14, max. 40 Watt (not included).
PAGE 13
 Fine-adjusting the door closed position - Loosen the bolts (A) Move the door pull arm in the direction of the arrow. Re-tighten the nuts and bolts fully.  Fine-adjusting the door open position - Loosen the bolts (A) Move the door pull arm in the direction of the arrow. Re-tighten the nuts and bolts fully.
PAGE 14
Operator panel indications O PERATORcontrol CONTROL PANEL INDICATIONS LEGEND LED off: LED illuminated: LED blink: LED rapid blink: red and green LED blink in alternation: red and green LED blink rapid in alternation: button pressed: button not pressed:         Green illuminated LED indicates door is open Red illuminated LED indicates door is closed Red & Green illuminated indicates door is in between open & close position No illuminated LED indicates door is in movement Page 14 14
PAGE 15
Operator control panel indications OPERATOR PROGRAMMING P Learn transmitter code 1. 1. 2. 3. 4. 2. 3. 4. Press  and  simultaneously (red & green will blink after 3 sec.) Release buttons (red & green illuminated) Press Transmitter to ‘learn’ your code (red & green blink fast) Press  to enter and store code P Programming Beam Break (where supplied) 1. 2A. 2B. 3. Please note: Microprocessor is still in program mode after having learned the transmitter code.
PAGE 16
Operator panel diagnostics OPERATORcontrol CONTROL PANEL DIAGNOSTICS The operator control panel indicates type of error.
PAGE 17
Programm Buttons buttons Programm    Indications Indications Door is open Door is closed Door is in between open & close Door is moving Error diagnostics Error Diagnostics Actuated force control opening door. Actuated force control closing door. Defect or Non-connect beam break. Defective printed circuit board.
PAGE 18
TTroubleshooting ROUBLESHOOTING Door does not close even though power is connected. Door stops and reverses in closing motion. - Check limit clip positions; is open switch on correct side of chain or belt? - Check if operator is programmed to have a beam break? - Check beam break NOTE: IN CASE ONE HAS TO CLOSE THE GARAGE DOOR IT IS POSSIBLE WHEN ONE PRESSES THE WALL CONTROL BUTTON CONTINUOUSLY - Check closing push force settings Door stops in opening motion. Door does not close or open completely.
PAGE 19
Manufacturers Declaration We hereby declare that the product referred to below, with reference to its design, construction and to the version as marketed by us, conforms to the relevant safety and health requirements contained in the European Council Directives pertaining to electromagnetic compatibility, machines and low voltage. This declaration becomes null and void in the event of modification or changes to the product not expressly agreed with us.
PAGE 20
NL Copyright. Door de auteurswet beschermd. Niets uit deze uitgave mag worden verveelvoudigd en/of openbaar gemaakt door middel van druk, fotokopie, microfilm of op welke andere wijze dan ook zonder voorafgaande toestemming van de uitgever. Technische wijzigingen voorbehouden. Centurion Deuren B.V. Koningsweg 2-13, 3762 EC Soest. Telefoon (035) 60 30 982 www.centuriondeuren.nl Showroom: Nijverheidsweg 24 in Soest (alleen op afspraak). EN 55011 EN 50081 EN 50082 ETS 300220 Art.-Nr.: 71 003 Version: 12.