Instruction manual

28 29
Glossary
A
Access Control : Primarilyreferstoa device orsetofdevicescontrollingtheentry of people
travellingthroughadoororsetofdoors.
Amplitude Shift Keying (ASK) : ThetypeofdatacommunicationsbetweentheProximityCard
andtheproximityReader.
ASK : Anabbreviationof“AmplitudeShiftKeying”.
B
Back Tamper : Theelectronictampersignaladvisingthecontrollerthatthecontrollerhasbeen
removedfromthewall.
Bypass Code : The4digitcodeusedtochangetheModeofOperationoftheSA1DKfromNor-
maltoBypassModeorviceversa.
Bypass Mode : AModeofOperationwheredooraccessisnotrestrictedtovalidusers.Inthis
modethedoormaybereleasedbyanyonepressingthebellbutton.
C
Cards : SeeProximityCards
Case Tamper : Theelectronictampersignaladvisingthecontrollerthatthecasehasbeenopened.
D
Default Factory Setting : Thesettingsthatthecontrollerispreprogrammedwithwhenthecontroller
ismanufactured.
Direct Shunt Delay : Thedelaytime(userprogrammed)usedinDirectShunt(SeeDirectShunt).
Door Bell : ThealertsoundactivatedwhenthedoorbellbuttonontheSA1DKispressed.(Requires
theBL-D40ExternalSounder)
Door Chime : Thealertsoundactivatedwhenthelockstrikeunlocksthedoorafteravalidcodehas
beenpresented.(RequirestheBL-D40ExternalSounder)
F
Fail Safe : Thesystemsettinginwhichatotalpowerlossleavestheconnecteddoorunlocked.
Fail Secure : Thesystemsettinginwhichatotalpowerlossleavestheconnecteddoorlocked.
L
Lock Strike : Termusedfortheelectronicorelectromagneticdoorlockusedforlockingorunlocking
thedoor.
Lock Strike Release Time : Theamountoftime(userprogrammed)thattheLockStrikeremains
unlockedwhenavalidcodeisentered.
M
Master User : AuserwhichhasaPrimaryandSecondaryCodewhicharethesame,andcangain
accessinanyModeofOperation.
Mode of Operation : Thestateofoperationofthecontroller.There are 3“Modes”.NormalMode,
BypassMode,andSecureMode.
N
Normal Mode : Thesystemsetting(Modeofoperation)inwhichallvalidusershaveaccessupon
presentingavalidProximityCardorPINCode(PrimaryCode).
Normal / Bypass Code : The4digitcodeusedtochangethecontrollersModeofOperationfrom
NormaltoBypassModeorviceversa.
Normal / Secure Code : The4digitcodeusedtochangethecontrollersModeofOperationfrom
NormaltoSecureModeorviceversa.
Normal User : AuserwhoonlyhasaPrimaryCodeandcanonlygainaccessinNormalMode.
Normally Closed : Arelayoutputfromthecontrollerthatisactivated(closedcircuit)undernormal
conditions.
Normally Open : Arelayoutputfromthecontrollerthatisde-activated(closedcircuit)undernormal
conditions.
O
Open Code 1 : The4digitcodeusedtoactivatetheLockStrikeRelayfortestingpurposesduring
installation.
Open Code 2 : The4digitcodeusedtoactivatetheLockStrikeRelayfortestingpurposesduring
installation.
P
Primary Code : TheuniquecodeissuedtoenableaccessinNormalMode.Userswithonlyprimary
codesareNormalusers.
Programming Code : The4digitcoderequiredwhenenteringprogrammingmode,deletingusers,
andresettingtheSA1DKtoitsfactorydefaultsettings.
Programming Mode : ThemodeusedwhenprogrammingtheSA1DPsystemsettings.
Proximity Cards : Electronically numbered IDbadges allocatedto systemusers and readby the
ProximityCardReader.
R
Relay : AnelectronicallycontrolledswitchusedforprovidinganOpenCircuitorClosedCircuitoutput
toexternaldevices.
REX : Anabbreviationof“RequestToExit”.
Request To Exit (REX) : Referstoabuttonwhichcanreleasethedoorfrominside.Commonly
locatedatthereceptiondesk,ornearadoorasanemergencydoorrelease.
S
Secondary Code : AnadditionalcodeissuedtoenableaccessinSecuredMode.Userswithnon-
identicalPrimaryandSecondaryCodesareSecureUsers.UserswithidenticalPrimaryandSecondary
CodesaremasterUsers.
Secure Mode : Thesystemsetting(ModeofOperation)inwhichonlyvalidSecureandmasterUsers
haveaccessuponpresentingavalidcode.
Secure User : AuserwhichhasaPrimaryCodeandSecondaryCodethatarenon-identical,andcan
gainaccessinanyModeofOperation.
Strike : SeeLockStrike
T
Tamper Siren : ThealertsoundactivatedwhenabackTamperorCaseTampereventoccurs.
(RequirestheBL-D40ExternalSounder)
Tamper Siren Time : Thetime(userprogrammed)thattheTamperSirenwillsoundwhenactivated).
Terminal Block : TherectangularconnectorsonthePCBusedtoattachwiringfromexternaldevices.