TA L K S W I TC H D O C U M E N TAT I O N START GUIDE RELEASE 4.10 C T.T S 0 0 5 .
INTRODUCTION About this guide This guide describes the steps required to do basic installation and configuration of your TalkSwitch telephone system. Once you have completed these steps, your system can be further customized for your needs. For complete configuration details, refer to the TalkSwitch User Guide. This guide is intended for use with TalkSwitch CA, CVA or VS models.
BEFORE YOU BEGIN Check package contents Whether you have purchased a system with one or multiple TalkSwitch units, each package you receive should include the following: • • • • • • • TalkSwitch unit TalkSwitch Configuration Software CD AC adapter RJ-11 telephone cables (1 for each incoming line) RJ-45 Ethernet cable or USB cable (for 24-CA) Quick Reference Cards for each extension Wall mounting template, screws and anchors for optional wall-mounting of your TalkSwitch unit.
STEP 1 — INSTALL THE TALKSWITCH SOFTWARE 1. Ensure that you have Administrator privileges on your Windows Vista, XP or 2000 system. 2. Turn your computer on and insert the CD into the CD-ROM drive. 3. The Install main window will appear within 20 seconds. Click INSTALL and follow the instructions. If the installation program does not automatically start (for example, if Autorun is disabled on your PC): 1. From the desktop, double-click the My Computer icon. 2.
STEP 2 — CONNECT TALKSWITCH TO YOUR PC OR NETWORK TalkSwitch can be set up anywhere in the vicinity of your incoming phone lines and computing equipment. • TalkSwitch 48-CA, 48-CVA and VS models can be connected to your PC using • a Local Area Network (LAN) or USB connection. CA models also offer a Serial (RS-232) connection. The TalkSwitch 24-CA can be connected to your PC using a USB or Serial connection.
STEP 3 — OPEN THE TALKSWITCH CONFIGURATION SOFTWARE Double-click the TalkSwitch icon on your desktop (this icon was created during the software installation), or from the Start menu, select Programs -> TalkSwitch 4.10 -> TalkSwitch Configuration 4.10. TalkSwitch Software will now attempt to detect your unit, displaying the progress on a Detecting TalkSwitch Units window. When the software detects your TalkSwitch, a progress bar appears while TalkSwitch transfers information to the PC.
STEP 4 — CONFIGURE AN AUTOMATED ATTENDANT An auto attendant can be set up to answer incoming calls and play a recorded greeting. For example, an auto attendant greeting can instruct callers to dial their party’s extension or reach a particular area of the company. If you do not wish to set up an auto attendant at this time, you can proceed to the STEP 5 — Configure Incoming Telephone Lines. Set up an auto attendant 1.
STEP 5 — CONFIGURE INCOMING TELEPHONE LINES Setting up your incoming lines will customize TalkSwitch to fit the unique needs of your business. For example, you can set all incoming calls to be answered by an auto attendant, set certain extensions to ring before an auto attendant answers, or have calls go directly to voicemail. If you have not set up an auto attendant, proceed to the Set certain extensions to ring or direct calls to voicemail section on the next page.
Set certain extensions to ring or direct calls to voicemail Option 1 Option 1 To have certain extensions ring without playing an auto attendant, select Ring extensions only. Click the checkboxes next to the extensions to ring. Note: you can adjust the ring sequence by clicking Adjust Sequence. Option 2 Option 2 To have certain extensions ring for a time before the auto attendant is played, select Play auto attendant.
STEP 6 — SAVE SETTINGS TO TALKSWITCH This step will transfer the settings you have configured from your computer to the TalkSwitch system. In the TalkSwitch System Configuration window, select File -> Save to TalkSwitch... A progress bar indicates that the configuration information is being sent to the TalkSwitch system. STEP 7 — CONNECT TELEPHONES AND PERIPHERALS Connect incoming (external) telephone lines Important! Lightning and electrical surges can cause damage to TalkSwitch.
Dual-line connection (2 incoming phone lines per wall phone jack) Four-wire connector TalkSwitch VS units require that each phone line be connected to a separate TalkSwitch line jack. Use singleline cables or a dual-to-two-single jack adapter. 2-line unit 4-line unit L3 L4 For TalkSwitch 48-CA and 48-CVA, connect a four-wire RJ-11 telephone cable to the wall phone jack of the incoming phone lines and the other end to the L1/L2 jack of the TalkSwitch unit.
Take note of which telephone is connected to which jack and refer to the table below for corresponding extension numbers. For systems with multiple TalkSwitch units, refer to the Networking TalkSwitch on a LAN section on page 13 for further details.
STEP 8 — AUTO ATTENDANT AND VOICEMAIL GREETINGS If you have set up an auto attendant, as described in STEP 4 — Configure an Automated Attendant, you should load or record a greeting now. What should an auto attendant say? The following is an example of a typical auto attendant greeting: “Welcome to the ABC company. If you know your party’s three-digit extension you may dial it now. To reach reception, press ‘0’ or stay on the line.
NETWORKING TALKSWITCH ON A LAN Up to four TalkSwitch units* can be networked over a LAN to increase the number of lines and extensions in your system. Connect TalkSwitch units Use Ethernet (RJ-45) LAN cables to connect each TalkSwitch to your Ethernet switch. Note: TalkSwitch unit enclosures are not designed for stacking. We recommend wallmounting the units in a horizontal row to maximize airflow prevent overheating. Power up all TalkSwitch units 1.
Changing TalkSwitch unit ID numbers Each TalkSwitch unit is pre-programmed at the factory with unit ID number 1. When you plug multiple units in for the first time or add one or more units to an existing network, the lights on the front of each TalkSwitch will flash. This is an indication that all units have the same ID number. Change the ID numbers so that they are all unique, as follows: 1. Connect a phone to any extension jack (eg.
SETUP COMPLETE Congratulations! Your TalkSwitch system should now be ready to accept incoming calls. TIP: Put a TalkSwitch Reference Card next to each extension phone to help employees become familiar with the TalkSwitch features. Configuring TalkSwitch units remotely Once installation is complete, you can configure your TalkSwitch units via a TCP/ IP connection between TalkSwitch and a remote PC running the TalkSwitch configuration software. For details, refer to the TalkSwitch User Guide.
© TalkSwitch 2007. All Rights Reserved. CT.TS005.002503 (March 2007) TalkSwitch is a division of Centrepoint Technologies Inc. TalkSwitch and the TalkSwitch logo are registered trademarks of Centrepoint Technologies Inc.
