Specifications

17
Advancing Slide 97118/97119
The Advancing Slide System consists of a pneumatic double acting, dual piston cylinder. The mounting bracket eases
precise positioning of either valves or rotorsprays. Additionally the system is equipped with 2 integrated limit switches
that provide position sensing when connected to a controller.
The forward movement of the advancing slide is initiated by the start signal. The Loctite
®
Controller 97152 or 97153
controls the forward and backward movement of the advancing slide. The magnetic fi eld of a permanent magnet
located on both pistons of the pneumatic cylinder effects contactless actuation of the electrical proximity switches at
their end positions, initiating the start of dispensing.
Technical Specifi cations:
Air Supply min. 4 bar (60 psi), fi ltered
to a maximum of 30µm
Dimensions (W x H x D) 97118: 80 x 65 x 30mm
97119: 150 x 65 x 30mm
Max. Stroke 97118: 50mm
97119: 100mm
Features:
• Allows simple and precise
positioning of valves and
rotorsprays
• Air fl ow controls to adjust
advance and retract speed
• Easy installation with Automatic
Controllers 97152 or 97153
• Reed switch with 4-pin M12
circular connectors for sensing
the two end positions
Rotorspray 97115
With the Rotorspray 97115, low to medium viscosity Loctite
®
products can be applied to the interior cylindrical
surfaces of workpieces. The Rotorspray is operated in combination with dispensing valves 98009, 97113 or 97135.
Loctite
®
controllers 97152 or 97153 are used for synchronized control of these units. The special design of drive
assembly and rotor housing ensures that the rotorspray is sealed to prevent contamination with adhesive.
Rotorspray 97115 is clamped in a fi xture. The dispensing valve is clamped in the rotorspray fi xture with the tip of the
fl exible dispensing needle pointing toward the inside of the wetting holes on the rotor disc. Loctite
®
controller 97152
or 97153 is used for switching the rotorspray ON and OFF and for opening the dispensing valve after the rotor reaches
the rated speed. As long as the dispensing valve is open, product is dispensed through the wetting holes of the rotor
disc by centrifugal force and uniformly distributed onto the interior cylindrical surface of the part. The rotorspray drive
assembly is a spring-loaded design to prevent damage by collision.
Technical Specifi cations:
Power Supply 24 VDC Adjustable Speed Range 4000-8000rpm
Power Consumption 10W, to 24W for short periods Weight 600g
Dimensions (W x H x D)
with standard rotor disc
ø 35/40 x 305 x 70mm
Features:
• Integrated error check, controlled
speed and overload shut-off
• Status of rotorspray indicated
by LED’s
• High speed for large and
small rotor discs
• Reduced risk of damage by
collision due to spring-loaded
design
• Short cycle time due to
quick-stop capability
Proximity Switch Unit Z3205
The mounting stand with integrated initiator is a small device with a universal workpiece receptacle and a dispensing
valve holding fi xture. Equipped with an appropriate dispensing valve, it is a useful tool for coating small parts,
e.g. screws, bolts, sleeves and bushes.
The operator positions the part to be coated manually in the workpiece receptacle. The initiator positioned behind
detects the part and sends a start signal to the Loctite
®
controller to trigger the dispensing cycle. Dispensing valve
holding fi xture and workpiece receptacle are adjustable and can be adapted to various part confi gurations.
As an option this unit is also available with a capacitive initiator for detecting stainless steel and plastic parts.
Technical Specifi cations:
Power Supply 24 VDC Dimensions (W x H x D) 100 x 185 x 150mm
Features:
• Universal tool to aid with
adhesive application
• Adjustable position of
dispensing valve
• Drip cup
• Rugged design