STRAIGHT LINE MINI SANDER Model 97956 SET up AND OpERATING INSTRucTIONS Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein. Distributed exclusively by Harbor Freight Tools®. 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in serious injury. SAVE THIS MANuAL.
Save This Manual NOTICE is used to address practices not related to personal injury. Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number). Keep this manual and the receipt in a safe and dry place for future reference.
Personal safety a. Stay alert. Watch what you are doing and use common sense when operating the tool. Do not use the tool while tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating the tool increases the risk of injury to persons. b. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep hair, clothing, and gloves away from moving parts.
f. Maintain the tool with care. Keep the Sandpaper sharp and clean. A properly maintained tool, with sharp, clean Sandpaper reduces the risk of binding and is easier to control. g. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operation. If damaged, have the tool serviced before using. Many accidents are caused by poorly maintained tools. There is a risk of bursting if the tool is damaged. h.
Code § 25249.5, et seq.) WARNING: The brass components of this product contain lead, a chemical known to the State of California to cause birth defects (or other reproductive harm). (California Health & Safety code § 25249.5, et seq.) Symbol Definitions Symbol Property or statement WARNING marking concerning Risk of Hearing Loss. Wear hearing protection. WARNING marking concerning Risk of Respiratory Injury. Wear NIOSHapproved dust mask/respirator. WARNING marking concerning Risk of Explosion. 3.
first be examined by a doctor and then have regular medical checkups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use.
Initial Tool Set Up/ Assembly Male Connector Tool Read the entire Important Safety Information section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Quick Coupler Valve Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram near the end of this manual. Unpacking When unpacking, check to make sure that the item is intact and undamaged.
the air tool to retain pressure and operate accidentally after the air supply is disconnected. Note: Air flow, and therefore tool performance, can be hindered by undersized air supply components. 3. The air hose must be long enough to reach the work area with enough extra length to allow free movement while working. 4. Make sure the tool’s Trigger (19) is in the off position; refer to “Components and Controls” section for description of controls. (See Figure A.) 5.
1. This Straight Line Mini Sander uses PSA, 11” long x 2-3/4” wide Sandpaper. 2. To attach Sandpaper to the Pad (34) of the Mini Sander, first wipe pad surface face of dust and debris. Next remove the protective covering from the glued side of the Sandpaper. Then attach the glued side of the Sandpaper to the Pad. (See Figure A.) 2.
User-Maintenance Instructions Procedures not specifically explained in this manual must be performed only by a qualified technician. To prevent serious injury from accidental operation: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the Trigger (19) before performing any inspection, maintenance, or cleaning procedures. To prevent serious injury from tool failure: Do not use damaged equipment.
Problem Troubleshooting Possible Causes Decreased output. 1. Not enough air pressure and/ or air flow. 2. Obstructed trigger. 3. Incorrect lubrication or not enough lubrication. 4. Blocked air inlet screen (if equipped). 5. Internal air leaks. 6. Mechanism contaminated. Housing heats during use. 1. Incorrect lubrication or not enough lubrication. 2. Worn parts. Severe air 1. Cross-threaded housing leakage. components. (Slight air leakage is normal, 2. Loose housing. especially on older tools.) 3.
pARTS LIST & ASSEMBLY DIAGRAM part # Description Qty. part # Description Qty.
Limited 1 Year warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equipment).
