User Manual

ManualsBrandscelsicom ManualsMoisture Measurementcelsicom MM611 Moisture Measurement in Wood

User manual

MM611

Quick Guide

At the moment the Celsiview cloud service version two can be tested, it can be accessed by click-

ing on the ”Celsiview 2 Beta” button on celsiview.se. The instructions below are based on Celsiview

Click on the ”Create new account” button. Fill in all the information needed to create the account.

A verication email will then be sent to the email address provided in the registration process.

Click on the link in the email to verify the account. If you do not receive an email, please check the

spam mail. Once the account is veried, a page will appear with a link to the login page.

Adding the sensor to your sensor register

Go to the Celsiview 2 login page by clicking on ”Celsiview 2 Beta” on celsiview.se and log in. Select

” Sensor ” in the menu and then ” Add new sensor ”. Now scan a sensor or enter the data manually

(S/N + control code written on the sensor). After the sensor data is displayed, click on ”Add this

sensor”. The cost of the sensor is now presented. Accept by adding the sensor to the shopping bas-

ket. Now scan the remaining sensors in the same way before proceeding to checkout.

Click on the shopping basket and view the contents. A summary of the costs is now displayed. Se-

lect or create an invoice recipient. The invoice recipient should contain all the information needed

to be accepted by your nance department. The references, cost centre, etc. will appear on your

invoice. Click on ”Complete transaction” to activate the sensor.

Start and activate the sensor(s)

Hold the grey sensor in both hands, place your right and left thumbs on top of the °celsicom logo

on the top of the sensor. Now slide the lid upwards/forwards to open it.

Insert 2 alkaline AA/LR6 batteries (1.5V) into the battery holder. The sensor will now beep to indi-

cate that it is booting up and the orange LED will light up. Both orange and green LEDs will light

up shortly afterwards in a constant light while the sensor is searching for a mobile connection.

The connection to the mobile network may take several minutes.

When the sensor is properly connected, the orange LED goes out and the green one starts ashing

and three short beeps are heard. The green LED now ashes the mobile signal strength every 30

seconds for three minutes. 3 blink=high level, 2=medium and 1=low. Feel free to move the trans-

ducer to achieve the best possible strength. A better signal strength gives a longer battery life.

After three minutes, the sensor switches to measuring/logging once every hour and transmitting

Summary of content (4 pages)

PAGE 1
User manual MM611 Quick Guide Register as a customer and create an account for the Celsiview cloud service At the moment the Celsiview cloud service version two can be tested, it can be accessed by clicking on the ”Celsiview 2 Beta” button on celsiview.se. The instructions below are based on Celsiview 2. Click on the ”Create new account” button. Fill in all the information needed to create the account. A verification email will then be sent to the email address provided in the registration process.
PAGE 2
all logged data every three hours to save battery power. Measurement and transmission intervals are adjustable in the Celsiview cloud service. Measuring more often than once every hour will affect the properties of the wood material (measurement object) and may result in inaccurate readings. To restart the above process or if the sensor does not connect properly, disconnect one battery, wait 60 seconds and reconnect it again.
PAGE 3
Add alarm recipients Log in to the account. Click on ”Administration” > ”Alarm recipients”. in the left hand menu. Add the required information of the alarm recipient using the button (+ Add new alarm recipient). Test the alarm by clicking on the mail box symbol of the recipient to which the test should be sent. NOTE! Check that it arrives. Other information Stainless steel screws work well as measuring points in the measurement object (wooden structure).
PAGE 4
User manual MM611 Model Measured value Range Maximum deviation MM600P1 Temperature Resistance (normal) Resistance (max) Moisture ratio Fur Wood Trätek (normal) Moisture ratio Fur Wood Trätek (max) Protimeter WME A (normal) Protimeter WME A (max) -30°C to +70°C 200kOhm to800MOhm 50kOhm to 1GOhm 12% to 26% 11,5% to 45% 10% to 25% 9,5% to 50% ±2°C (0-30°C) ±15% Not defined ±3% of measured value Not defined ±3% of measured value Not defined Connection NB-IoT (LTE Cat NB1) B20.