CTR-180 M2M Router Manual CTR-180 User Manual V1.
CTR-180 M2M Router Manual Contents 1. Introduction 1.1 1.2 Feature Package Contents 2. Name of each section and features description 2.1 Name of each section 2.2 LED Display 2.3 Getting Started. 3. Using Configuration Menu Connecting CTR-180 to PC 3. 1 OverView 3. 2 Internet 3.2.1 Internet > WAN 3.2.2 Internet > LAN 3.2.3 Internet > DHCP Clients 3.2.4 Internet > Advanced Routing. 3.3 Wireless Setting 3.3.1 Wireless > Basic 3.3.2 Wireless > Advanced 3.3.3 Wireless > Security 3.3.4 Wireless > AP Client 3.
CTR-180 M2M Router Manual 1. Introduction This manual is for users who use CTR-100 as 3G Wi-Fi Router. For the pursoe of 3G M2M appliction, please contact to Celot Wireless. 1.1 Feature CTR-180 provides functions as follows; ● CTR-180 enables you to access to the internet by using wireless network (CDMA REV.A network). ● CTR-180 supports multi-interfaces including USB, Full UART (RS232C/RS485), Lite-UART, I2C and RJ.
CTR-180 M2M Router Manual 1.2 Package Contents 5V DC Power Adaptor CDMA Antenna Battery Pack (optional) CTR-180 GPS Module (optional) ※ Note Pictures in User Manual might be different from the actual product you purchased. Furthermore, some of the components might be changed for better performance without any prior notice.
CTR-180 M2M Router Manual 2. Name of each section and features description 2.
CTR-180 M2M Router Manual ※ External Interface 2.2 LED Display No. Assignment Color Status Remarks LED1 3G RSSI Various ON Yellow Green -> Orange -> Red (from Strong to week signal) LED2 3G RED ON When the device is connected to 3G network. LED3 WLAN RED ON When WLAN is activated. LED4 POWER RED ON When the device is power on. 2.3 Getting Started. 1). Open Rear Cover and Insert SIM Card 2). Insert Battery and Close the Rear Cover 3). Connect Power adaptor to the device. 4).
CTR-180 M2M Router Manual 3. Using Configuration Menu Connecting CTR-180 to PC 1). Connect CTR-180 to PC through LAN cable or WIFI 2). For WIFI connection, the default Network ID (SSID) from the factory is CTR-180 3). To access to Web UI page, Input http://10.10.10.254 in the address window as shown below and press Enter Key 4). User Name and Passwords are required to access adimin web page. Plesae input “ admin” for User Name and “admin” for Password when you acess the Web UI first time. 5).
CTR-180 M2M Router Manual 3. 1 OverView Basic network information can be displayed. ● Select Language: Supported languages can be selected. 3. 2 Internet 3.2.
CTR-180 M2M Router Manual WAN connection mode for CTR-180 is “3G/LTE” as default but other types of WANs can be selected as follow, 1) STATIC (Fixed) 2) DHCP (Auto Config) 3) PPPoE(ASDL) 4) L2TP 5) 3G/LTE Mode ● Provided User ID, Password, Dial Number and APN should be input. 6) CDMA ※ Note You must input correct user ID, Password, and Dial Number from the wireless network provider (ex. Skylink etc) otherwise, the device is not able to access the wireless network. (ex.
CTR-180 M2M Router Manual This page is to configure the parameters for local area network which connects to the LAN port of your Access Point. Here you may change the setting for IP address, subnet mask, DHCP, etc.. ● IP Address: The basic IP address for CTR-100 is “10.10.10.254”. IP address for CTR-180 can be changeable on this menu. ● Subnet Mask : You can change Subnet Mask ● Default Gateway : You can change Default Gateway. ● - DHCP Enable: IP address can be automatically allocated to Client PC.
CTR-180 M2M Router Manual - You need to Input IP address and MAC address for the client PC and then click Apply Changes. - 3.2.3 Up to 3 Static IP can be available. Internet > DHCP Clients DHCP Clients connected to CTR-180 can be monitored on this page. 3.2.4 Internet > Advanced Routing.
CTR-180 M2M Router Manual CTR-180 can add and remote custom internet routing and enable dynamic routing exchange protocol. ● ADD a routing rule - Input IP range for “Destination”, - Select Range (HOST/NET) - Input value for ”Netmask”, - Input IP for ”Gateway” - Select Interface (LAN/WAN/Custom) and input IP ● - Dynamic Routing You can select Disable/Enable 3.3 Wireless Setting 3.3.1 Wireless > Basic 1). CTR-180 was released from the factory without any wireless security for user’s convenience.
CTR-180 M2M Router Manual This page is to configure the parameters for wireless LAN clients which may connect to your Access Point. You can change wireless encryption settings as well as wireless network parameters. 1). WIFI OFF : WIFI shall be OFF by clicking it. 2). Network Mode : You can select Wireless Standard of CTR-180 x 11b/g/n mixed mode- 2.4GHZ(B+G+N) Using 802.11b/g/n.(Recommended) x 11b/g mixed mode- 2.4GHZ(B+G) Using 802.11b/g. x 11b only -2.4GHZ(B) Using 802.11b x 11g only-2.
CTR-180 M2M Router Manual 3). Network name SSID: You can change Network SSID, up to 30 characters can be input based on ASC II type. Also you can select Hidden or Isolated not to show the SSID to other clients. 4). Channel Number : You can select channel numbers for wireless network. The channel number is to be set up as factory default. If you select Auto, it will search for proper channel.
CTR-180 M2M Router Manual ※ Note We do not recommend any changes on the advanced setup if you are not aware of these features or you are not an expert 3.3.3 Wireless > Security Encryption Type Description Disable No use of Encryption. OPEN/WEP WLAN client need not provide its credentials to the Access Point during authentication SHARED/WEP the WEP key is used for authentication in a four step challengeresponse handshake WPA Stronger Encryption type than WEP using Passphrase.
CTR-180 M2M Router Manual 2). And chose one of types from TKIP, AES and TKIPAES for WPA Cipher Type. 3). Input passwords which you want to set in Pass Phrase, if required. 3.3.4 Wireless > AP Client CTR-110 can be used as an AP client. 1) You need to check the followings for the AP which you want to connect to - SSID - Security Mode - Encryption Type - Password 2) For AP client setting, , go to Wireless > Basic - Select the same channel with the channel for AP.
CTR-180 M2M Router Manual - Select AP Client Input SSID for AP Select Security mode for AP Select Encryption Type for AP Input Password for AP. Click [Apply] 4) If AP Client IP is displayed as the picture above, CTR-120W works as an AP client. If not, “Disconnected” is shown instead of IP address. 3.3.5 Wireless > WPS 1) WPS function can be enabled on this menu. 2) You can set WPS function after enabling it from this page and then press WPS Key on the device. 3.3.
CTR-180 M2M Router Manual 3.3.7 Wireless> Statistics Wireless LAN TX & TX DATA is available on this menu.
CTR-180 M2M Router Manual 3. 4 Firewall 3.4.1 Firewall > MAC/IP/Port Filtering Settings 1). Basic Settings: ● MAC/IP Port Filtering : If Enabled, Filtering will be available. ● Default Policy : ● Dropped : Only allowed MAC/IP Port (listed) in the “MAC/IP/Port Filtering Settings” window can access to the router. ● Accepted : Only listed MAC/IP Port in the “MAC/IP/Port Filtering Settings window restricted to access to the router. 2).
CTR-180 M2M Router Manual 3.4.2 Firewall > Port Forwarding Settings It will allow Client PC to be used for specific service or server. ● IP Address: IP address for server needs to be input and the server PC should operate by server S/W. ● Port Range: Input Port range for service. ※ 80 port is not allowed in Port. This port is only for remote admin. ● 3.4.3 Protocol : Input one form TCP, UDP, TCP&UDP.
CTR-180 M2M Router Manual It will allow the PC to be open for every internet user. PC with DMZ enabled can communicate all of internet users and servers. ● Select Enable DMZ Setting to use DMZ. ● DMZ IP Address: 3.4.4 Input client IP address.
CTR-180 M2M Router Manual 3.4.5 ● Firewall > Contents Filtering Contents Filter Settings You can set certain contents of WEB to be restricted. ● Webs URK Filter Settings You can set certain Web sites to be restricted to access. Input URL address and click [ADD] then it will be shown in the “Current Webs URL Filter” and also the listed URLs are restricted. ● Wes Host Filter Setting You can restrict WEB URL containing certain words.
CTR-180 M2M Router Manual 3.5. Administration 3.5.
CTR-180 M2M Router Manual 3.5.
CTR-180 M2M Router Manual 3.5.3 Administration>Management ● Administrator Setting This menu is to change Account (User name) and Password for the first log in page. Factory default for administrator settings is “admin” for User name and “admin” for password as shown below.
CTR-180 M2M Router Manual ● ● NTP Setting ● Sync with NTP server to set Current time ● Select Time Zone ● Input NTP Server ● Input time for NTP Sync time (hours) DDNS Setting - CTR-180 will update the DNS server with its IP addresses when a network supports Dynamic DNS (DDNS). 3.5.4 Administration>Upload Firmware This page is to upgrade Firmware and boot loader ● To Upgrade the SW of CTR-180, click [Browsing] Icon, choose the right BIN file and click [APPLY] Icon.
CTR-180 M2M Router Manual This page is to save current settings on a file or reload the settings from any file which was saved previously. Besides, you could reset the current configuration to factory default. 1). Export Settings To save the current setting Click [Export] button and below picture will be displayed. Then click [Save] button and save[Config.dat file] in the desired path. 2). Import Setting When changing the setting of CTR-180 by using the already saved [Config.
CTR-180 M2M Router Manual In order to return Factory Default Settings window, click [Load Default] button, then the new message window will be displayed. Then, click [OK] button and CTR-180 will be changed to the factory setting. 3.5.6 Administration> Reboot Settings You can manage CTR-180 system reset in this menu. 1) Auto Reboot In case Auto Reboot is enable, CTR-180 can be reset based on pre-defined schedule.
CTR-180 M2M Router Manual 3.5.7 Administration>System log This page is to set remote log server and show the system log.
CTR-180 M2M Router Manual 3.6.1 Service> Direct Serial CTR-180 supports “Direct Serial” via Full UART and Lite UART to transfer Serial raw DATA from a device to a server. The Serial device can work as if it is connected to the server directly. ● ● ● Status Setup : Select “Enable” Device Setup : Select Serial port, Baudrate, DATA bit, Party, Stop bit and Flow Control etc Server Setup : Input server IP and its Port.
CTR-180 M2M Router Manual 3.5.8 Service> Serial Test CTR-180 supports Full UART and Lite UART for interface with other device. This menu is to test Full UART and Lite UART and to see the DATA from the devices connected to CTR-180 via Full UART or Lite UART. ● Serial Device ● Select Serial port [Lite UART or Full UART] and right baud rate for the device. ※ GPS module & antenna Serial port for GPS is Lite-UART and baud rate is 9600.
CTR-180 M2M Router Manual CELOT WIRELESS 32
CTR-180 M2M Router Manual Technical Specification ● Standards : IEEE 802.11g ,IEEE 802.11b, ,IEEE 802.11b ● Security : ● WLAN Frequency Range : 2.4GHz to 2.483GHz ● Memory : RAM 64MB, Flash Memory 8MB (4MB is reserved for customer S/W) ● CDMA Standard : IS-95 A/B, IS-98A, IS-637A, IS-707A, IS-2000, IS-835, IS-856, 64/128-bit WEP, WPA-PSK, WPA-PSK2 IS-866, IS-890 ● CDMA Frequency Range : A Band : RX : 462.5 ~ 467.475 MHz / TX : 452.5 ~ 457.475 MHz L Band : RX420.000 ~ 424.
CTR-180 M2M Router Manual CELOT Wireless CO., Ltd 4Fl.,NongHyup Bldg.,#1588-10 Gwanyang-Dong, Dongan-Gu, Anyang City, Gyeonggi-Do, Korea (Postal Code : 431-727) Tel : +82 70 7458 5501 Fax: +82 31-388 5501 http://www.celotw.co.
