Technical data

ManualsBrandsCellution ManualsComputer equipmentLinkWiser-S400M

Narrowband Multi-channel

Data Radio Modem

LinkWiser™-S400M Rev. 2.1

Technical data & Users’ Manual

Summary of content (18 pages)

PAGE 1
Narrowband Multi-channel Data Radio Modem LinkWiser™-S400M Rev. 2.
PAGE 2
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 INDEX 1. REVISION HISTORY...................................................................................................................................... 3 2. PRODUCT OVERVIEW.................................................................................................................................. 3 2-1. PICTURE ..............................................................................
PAGE 3
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 1. REVISION HISTORY REVISION 2.0 2.14 SIGNED JN Lee JSM, KYC DATE DESCRIPTION 15/10/2010 Document created 21/9/2011 Sleep current adjusted 2. PRODUCT OVERVIEW LinkWiser™-S400M Rev. 2.1 Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 series support a narrowband, 12.
PAGE 4
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 2-1. PICTURE 3. BLOCK DIAGRAM Cellution Inc. #317, NKIC, 48-84 Honguen-1dong, Seodaemun-gu, Seoul, Korea Zip: 120-760 Enquiries: sales@cellution.co.kr / support@cellution.co.
PAGE 5
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 4. FEATURES 9 9 9 9 9 9 9 9 9 9 9 9 9 9 9 simple 10 pin interface 2 different mode (Transparent, Address) programmable Repeater mode support Easy to use AT command set A few clicks only for configuration (No RF knowledge requirement) Low power consumption for battery operation Robust anti-interference HDLC protocol 12.5KHz of narrowband 424, 447MHz (Korea) Exceptional sensitivity (-113dBm @ 4.
PAGE 6
Technical Datasheet & User’s Manual Item no PIN 1 VCC 2 3 4 5 6 GND GND U/I RX_D TX_D 7 8 9 10 Sleep GND TRXTRX+ Description Level Connected to the terminal Power input 6.5VDC ~ 24VDC Power supply/Ground Power supply/Ground User Interface Serial data receiving end Serial data transmitting end Sleep control (input) end Power supply/Ground Serial data Serial data Narrowband multi-channel data radio modem DTE (User terminal) LinkWiser™-S400M Rev. 2.
PAGE 7
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 8. MAXIMUM RATINGS Operating temperature Storage temperature -30°C to +80°C -40°C to +85°C LinkWiser™-S400M Rev. 2.1 VCC (pin 1, 2) 6.5VDC ~24VDC 9.
PAGE 8
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 11. INTEGRATION GUIDE LinkWiser™-S400M Rev. 2.1 owns a voltage regulator which always supplies 2.8VDC to the entire circuit except POWER APLIFIER that receives 6.5VDC ~ 24VDC of input voltage directly. And this is for stable operation & performance especially in RF front end side. Nevertheless, qualified external power supply is necessary, which must be in 6.
PAGE 9
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 Please contact support@cellution.co.kr for more details. 12. CONFIGURATION This section describes the configuration and test commands supported by the radio module. In most cases, once the configuration is set it will not need to be changed. Configuration is performed using a serial terminal, or appropriate communication application.
PAGE 10
Technical Datasheet & User’s Manual ATO AT/V Register Handling Command Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 Communication mode activation ‘ATO’ command gives an instant access to the module’s Operating mode. ‘ATO’ command is used to get out of Configuration Mode. Answer: Good Bye! ‘AT/V’ command displays the module’s firmware version Ex) AT/V ‘S424V1.0’ // LinkWiser-S, 424MHz, V1.0 ‘HP915V2.0 // LinkWiser-HP, 915MHz, V2.
PAGE 11
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 ‘1’: Enabled R/W ATS132 Repeater Address Ex): Assuming that S130 = ‘0’ & S131 = ‘1’, the TX data will automatically routed to & by the repeater(address defined by S132) Repeater Address Ex): Assuming that S130=’1’, this register will set the desired repeater’s address. All data will be sent to the repeater node first, and that repeater will automatically route the data to the preset destination.
PAGE 12
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 The addressed mode is similar to a multipoint mode. All modules can communicate with each other by addressing each frame to one of them. 12-3-1 Operation Addressed mode’s purpose is to offer an optimal radio link performance providing the multipoint access of the transparent mode.
PAGE 13
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 424.8625 13 424.8750 14 424.8875 15 424.9000 16 424.9125 17 424.9250 18 424.9375 19 424.9500 20 Note: Listen-Before-Talk (LBT) must be applied. Tx is allowed in case of less than -90dBm of RSSI level only in all channels. And the continuous Tx is limited to 40 seconds only. Frequency channel table in 447MHz A band Frequency (MHz) 447.2625 447.2750 447.2875 447.3000 447.3125 447.3250 447.3375 447.
PAGE 14
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 12-4-2 Tx power control Reading: Reading: ‘AT+P?’ Answer: TxPower: 8 10dBm Writing: ‘AT+P=8’ // Set the Tx power at 8th level Answer: > Description: Power of the Radio Value 8 7 6 5 4 3 2 1 0 Tx power (dBm) < 10dBm < 9dBm < 7.9dBm < 6.3dBm < 4.4dBm < 2dBm < -1.3dBm < -7.0dBm < -40dBm 12-4-3 RSSI level Reading: ‘AT+CSQ?’ Answer: ‘n’ Description: ‘n’ is a realistic RSSI level in the unit of ‘dBm’.
PAGE 15
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 Figure1 Typical System Block Diagram Data is sent and received in standard ‘RS232’ serial format and there is no restriction on characters that may be sent. If you configure “Serial Link Time Out” value more than one byte interval, the data flow look like Figure2, but if you configure “Serial Link Time Out” value less than one byte interval, the data flow looks like Figure3.
PAGE 16
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 12-5-3 UART Timing in Tx You MUST configure the Serial Link Time Out value depending on DEPENDING ON YOUR SERIAL BAUD RRATE. EX) If your serial baud rate is 9600bps, we recommend over 1ms of the Serial Link Time Out value. Thus, you can get a result same as the above Figure2. 9600bits/second = 9600bps, then 960bytes/second because start bit & stop bit should be added.
PAGE 17
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 9600bps of baud rate & 4800bps of air rate in order to transmit 50 bytes of data. 12-6 TERMINAL SETTING A typical terminal setting 1. Please connect the LinkWiser-S400M to RS-232C in your PC. 2. Please make sure that the mode switch is set to RS-232C before power on. And also please make sure that the input voltage range is within 6VDC to 24VDC. 3.
PAGE 18
Technical Datasheet & User’s Manual Narrowband multi-channel data radio modem LinkWiser™-S400M Rev. 2.1 You can use the “Set Macros” function to make easier to write & read our AT command sets. However, “$0D$0A” string should be followed for carriage return in this case. Cellution Inc. #317, NKIC, 48-84 Honguen-1dong, Seodaemun-gu, Seoul, Korea Zip: 120-760 Enquiries: sales@cellution.co.kr / support@cellution.co.