Bluetooth Cellular Gateway
INSTALLATION OPTIONS 1. With Cell Phone(s) only OUTLET TELEPHONE I I I POWER SUPPLY I I I TELEPHONE CORD OR 2.With Home Line & Cell Phone(s) TELEPHONE OUTLET • OUTLET I • I I • I t ..... TELEPHONE CORD NOTE: * A hanging lid a) To plug the telephone cord into the [TEL.L1NE] jack, move the hanging lid to the left. b) To download the new Bluetooth firmware, you have to first DISCONNECT the telephone cord from the jack of [TEL.
STEP 1 Plug-in & Connect Plug the Power Adaptor from wall outlet into Cel12Tei Plug USB line cord from your computer+--" into Cel12Tei *Hanging lid........
STEP 2 Ready for Pairing Select line [Cell Phone 1], or [Cell Phone 2] on Cell2Tei Press and hold down button for selected ~ line for about ..,.,.
STEP 3 Pair Cellular Phone to Cell2Tei Amber light stops blinking and remains on when cellular and selected Cell2Teiline are paired successfully ~ YOUR CONNECTED! 4
OUTLETS Cell Phone line 1'-'Cell Phone line 2 Error correction light indicator POWER ADAPTER CONNECTION USB CONNECTION TELEPHONE SERVICE LINE CONNECTION (to wall outlet) ...... -.
NOTES - Each cell phone line can only be paired to ONE cell phone at a time. - A cell phone line can be paired to a different cell phone at any time by repeating the pairing procedure. - Previous pairing information is lost when pairing is initiated for the same cell phone line. - A paired cell phone line can be "unpaired" and prepared for re-pairing by holding down the line button until the amber light button blinks quickly.
CONTACT INFORMATION • CUSTOMER SERVICE & SUPPORT Should you have any questions regarding your Ce112Tel, please visit us at www.ceI12telgateway.com Made In China Copyright@Cell2Tel Ltd. Cel12Tei is a registered Trademark of Cell2Tei Ltd. All rights reserved. Cell2Tei Ltd. Los Angeles, CA.
~ , CELL2TEL ~
IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electric shock and/or injury to persons, always follow these basic safety precautions when using your Cel12Tei C2T-XT2000. 1. Read, understand, and follow all instructions. 2. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. If necessary, use a soft cloth lightly moistened with a mild detergent solution. 3.
d. unit to normal operation. If the unit has been dropped or the case has been damaged. e. If the unit exhibits a distinct change in performance. 8. Do not use the telephone to report a gas leak in the vicinity of the leak. 9. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. 10. Never install jacks in a wet location unless the jack is specifically designed for wet locations. 11.
SAVE THESE INSTRUCTIONS WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. CAUTION RISKS OF ELECTRIC SHOCK- DO NOT OPEN! To reduce the risk of electric shock, do not remove casing. AA No user serviceable parts inside. Refer servicing to qualified service personnel. The light flash with arrowhead symbol, within an equilateral triangle, is intended to alert user to the presence of dangerous voltage which may cause electric shock to persons using it.
CONTENTS INTRODUCTION .
INTRODUCTION Congratulations on your purchase of the Cell2Tei C2T-XT2000 Cellular Bluetooth Gateway. In addition to your regular telephone line you will now be able to access up to 2 Bluetooth enabled cell phones from any standard telephone connected to the Cell2Tei C2T-XT2000 via your cell phone's Bluetooth connection. Cell2Tei is designed to work with or without telephone service (land line). PACKAGE CONTENTS The Cell2Tei gift box includes the following.
* Fully compatible with any brand of home telephone * Direct access to home line by simply picking up the extension telephone * USB connection to download updates (firmware) for future cell * * * * * phone models Call Waiting through multi-line and multi-call Access cell phone voice mail, voice dialing and speed dialing* Force Call Connection* Error Installation/Connection tIx Indicator Individual LED Indicator for home line, Cell Phone Line 1 and Cell Phone Line 2 with distinctive ring patterns WARNJNG:
POWER ADAPTER CONNECTION seTUP TELEPHONE CORD CONNECTION USB L---_~-I---------...:....:~----J CONNECTION TELEPHONE SERVICE LINE * HANGING CONNECTION LID 1. Plug a standard corded or cordless I:l telephone into the Cel12Tei [PHONE] jack using a regular telephone cord. u-~~.~ ~ 2. IF a telephone service landline is used, plug the telephone service line into the Cell2Tei [TEL. LINE] jack using the cord from the wall. NOTE: * A hanging lid a) To plug the telephone cord into the [TEL.
* Cell2Tei and these types of cordless phones. Some wireless networks (Wi-Fi), such as 802.11 may interfere with Bluetooth radio signals. Keep as much distance as possible between this type of equipment, the Cell2Tei and your cell phones. J PAIR YOUR Bluetooth ENABLED CELL PHONE(S) to Cell2Tei Your Cell2Tei can be paired (connected) up to two different cell phones, one cell phone per Cel12Tei line. To pair a Bluetooth cell phone to a Cel12Tei line, complete the following steps: 1.
~ Cell Phone Line #1 9 k@ . ;J~- Co L I I :J 0 J~ Cell Phone Line #2 ) HINT: * phone Each cell phone line can only be paired to ONE cell at a time. * Aat cellany phone line can be paired to a different cell phone time by repeating the pairing procedure. * initiated Previous pairing information is lost when pairing is for the same cell phone line. * forA paired cell phone line can be "unpaired" and prepared re-pairing by holding down the line button until the * button flashes rapidly.
Manual Bluetooth Connection You may not want live cell calls to be transferred automatically or you may want to force your cell phone to disconnect from the Cel12Tei . V\lhen a cell phone line is connected (amber line status light remains on), press the said cell phone line button to disconnect that line. In this case, the amber light will turn off once disconnected and audio will be transferred to the cell phone so you can continue your call on the cell phone.
2. Simultaneously, press and hold Cell Phone 1 and Cell Phone 2 Line Buttons for approximately 4 seconds: all telephones connected to Cell2Tei should start ringing. i HINT: * If an extension telephone does not ring, check that the phone is properly powered and that all cables are properly connected. NOTE: Cel12Tei should support ALL telephones, including older analog telephones with DTMF dialing LINE STATUS & LIGHT INDICATORS Green Solid @ Indicates the unit is powered and operating normally.
Amber Rapid Flashing Indicates the selected cell phone line is in pairing mode. Use your cell phone to search and pair to the Ce 112Tel. Amber Uneven Flash Indicates the selected cell phone line is connected to a cell phone and there is an incoming call on this line. Amber Slow Flashing Indicates the selected cell phone line is paired but the cell phone is currently out of range and/or temporarily not connected. Cell2Tei is actively searching for this cell phone.
VVhen dialing out using a cell phone connected to the Cell2Tel,an optional [#] digit may be dialed at the end of the number to activate immediate dialing, the same as the "Send" button on the cell phone. Dialing a [#] is not required. The dialing process will start following a short delay after the last digit is dialed.
Receiving a Call When a cell phone has been paired and is currently connected with Cell2Tel, the telephone plugged into the Cell2Tei should also ring. Each line has its own distinctive ring pattern. You may also recognize which line is ringing by looking at the status light on top of the Cel12Tei. The amber light for a ringing cell phone line will flash with a unique cadence.
Voice Mail You can access your cell phone voice mail from an extension telephone. Before this feature will work you may have to program your voice mail number into Cel12Tei . Use the following steps to access cell phone voice mail: 1. Pick up an extension telephone. Listen for dial tone. 2. Optional: Select Cell Phone Line [1 ][Flash] or [2][Flash] 3.
Call Waiting Call Waiting for as many as 6 incoming calls! (2 calls per line max.) VVhile using the Cell2Tel, users may access the Call Waiting feature for as many as 6 calls at the same time. Calls may be received through the two Cell Phone Lines made possible via paired connections between the gateway and two Bluetooth enabled cellular phones. Calls may also be received via a third line made possible using landline service*.
NOTE: • Not all cell phones support this feature and not all cell phones enable Cel12Tei to access this feature. COMPUTER CONNECTIVITY Cel12Tei C2T-XT2000 has a USB port that allows Cell2Tei to communicate with a computer running the proper software, including XP and VISTA. TROUBLE SHOOTING Green light @ is OFF - indication of power failure Re-check the connection between the Cell2Tei and the 9-Volt DC Power Adapter (Refer to the Connection Diagram on page 2).
NO dial tone on extension telephone Check that the REO lighttrxon Cel12Tei is NOT ON. Ensure your extension telephone(s) are properly plugged into the Cel12Tei . If the GREEN light @ is not on, check the power cord is connected properly. See section UTesting the Setup" on page 6. Error/Busy tone on extension(s) No cell phones are currently connected. Ensure a cell phone that has been paired (see section"Pairing your Bluetooth Cell Phone to CeIl2Tel" ) with Cell2Tei is within range.
Voice mail access not working Voice Mail access may have dialed the wrong number. For this feature to work the voice mail number must be programmed for the desired line. See section on IIVoice Mail". How to check software version To check the Cell2Tei C2T-XT2000 software version, connect a caller 10 enabled telephone to the telephone line jack on the back of the unit. Simultaneously press and hold the Cell Phone Line 1 and Cell Phone Line 2 Buttons for approximately 4 seconds.
about repair or warranty information .If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
determine if it is causing the malfunction. If the equipment is determined to be malfunctioning, its use should be discontinued until the problem has been corrected. Current FCC regulations specify that any direct connections to a telephone company line be done using only standard phone jacks USOC RJ11 C and plugs that is TIA-1 096 -A compliant. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Calling 911 Calling 911 using a cell phone works differently then calling 911 using a land line. In order to complete a 911 call and in order for Emergency Services to provide your location, E911 services are required in your area and your cell phone must be GPOS enabled and service activated. Refer to your cell phone owner's manual to determine if your cell phone has that feature and make sure that the feature is activated.
parts and products, and products on which a refund may be made, become the property of Cell2Tei. New and reconditioned parts and products and should be warranted for the remainder of the original warranty period.
CUSTOMER SERVICE & SUPPORT Should you have any questions regarding your Cell 2Tel please Visit us at www.ceIl2telgateway.com Cell 2 Tel Ltd.
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details. FCC DoC Responsible Party: Name: CELL2TEL, USA Address: Los Angeles, CA.
