Operating instructions celexon Electric Professional Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting or operating this product. Please retain these instructions for future reference.
WARNINGS The purpose of these operating instructions is to familiarise you with the operation of this product. Therefore, keep these instructions in a safe place so that you can refer to it at any time. • Before installation, please refer to the enclosed data sheet for further safety and use instructions. • Do not begin installation until you have read and understood the complete operating instructions. • Carry out the installation with another person to ensure safe installation.
• Suspended loads must be checked for strength and load-bearing capacity at least twice a year. • Children should not use the screen or play under it unsupervised. • Caution: Risk of injury! The unit closes flush and firmly in its retracted state, keep fingers, hands or other small parts away from the opening. • All supply lines and cables must not be subjected to additional loads and must be laid in such a way that they are not damaged or crushed.
DISCLAIMER The information in this document is subject to change without notice by the manufacturer. Changes will be added to subsequent versions of this manual. Errors expected. CARE INSTRUCTIONS NEVER clean the screen with alcohol or other cleaning agents containing solvents.Use only a soft and clean cloth. If necessary, dirt can be removed from the surface with a mild soap solution (max. 5%). It is essential to avoid contact with pointed or sharp objects.
IN THE BOX 1x Screen 4x Nuts 4x Plastic dowels 2x Suspension loops 4x Screws 1x IR remote control incl. Batteries 2x Metal plates INSTALLATION NOTES Install the screen in a position that is fully visible to all viewers! The optimum installation height corresponds to the position of the viewers in the centre of the screen with the screen fabric extended: eye level = lower third of the screen surface.
Drill the holes at the markings at a diameter to match the diameter of the ring eyelet used, screw them firmly into the ceiling (according to the manufacturer‘s instructions and the load capacity of the screen) and hang the screen. MOUNTING ON THE CEILING (SCREWED) Measure the distance between the holes in the side caps (two per cap) and transfer them to the ceiling. Drill the holes at the markings to the right diameter for the mounting material, insert and screw the screen in place tightly.
MOUNTING ON THE WALL Measure the distance between the holes in the side caps (two per cap) and transfer them to the wall. Drill the holes at the markings with the holes with the right diameter for the mounting material and make sure that the drill holes are absolutely level (Use a spirit level!). Use dowels and screws that are suitable for your mounting surface. Screw the two upper screws into the wall most of the way and hang the screen from both sides into the upper hole.
OPERATION CONTROL VIA THE WALL CONTROL BOX STEP 1: SAFETY CHECK (FIG. 1) Insert the plug into the socket (ensure correct voltage). The cable must not be laid on hot surfaces or stretched. When using an extension make sure it has the correct specification. The wall control box must be mounted with the cable outlet on the underside. STEP 2: EXTEND THE SCREEN (FIG. 2) Press the downward pointing arrow button. The screen extends and stops automatically at the set end point.
CONTROL VIA THE REMOTE CONTROL STEP 1: SAFETY CHECK (FIG. 1) Insert the plug into the socket (ensure correct voltage). The cable must not be laid on hot surfaces or stretched. When using an extension make sure it has the correct specification. The wall control box must be mounted with the cable outlet on the underside.Make sure that there is a line of sight between the wall control box and the remote control. The IR eye on the box must not be covered. STEP 2: EXTEND THE SCREEN (FIG.
INFORMATION ON EU CONFORMITY Manufacturer: celexon Europe GmbH Address: Gutenbergstraße 2, 48282 Emsdetten, DE Product name: celexon Electric Professional Products that are marked with the CE mark meet all requirements of the relevant EU directives. The EU declaration of conformity can be downloaded from the following address: www.celexon.de/zertifikate The symbol indicates the separate collection of electrical and electronic devices in EU countries.
INFORMATION ON UK CONFORMITY Manufacturer: celexon Europe GmbH Address: Gutenbergstraße 2, 48282 Emsdetten, DE Product name: celexon Electric Professional Products that are marked with the UKCA mark meet all requirements of the relevant UK directives. The UK declaration of conformity can be downloaded from the following address: www.celexon.de/zertifikate The symbol indicates the separate collection of electrical and electronic devices in EU countries.
