IP-HOB-531-X OR SSP-511-X-SPK1.07r1-ISSUE4.0 SERVICE MANUAL FOR VoIP MODEL IP-HOB-531-X HANDS FREE WEATHER RESISTANT TELEPHONE OR MODEL IP-SSP-511- X HANDS FREE STAINLESS STEEL PANEL TELEPHONE EQUIPPED WITH SPK1.
ISSUE 4.0 IMPORTANT INFORMATION FOR CUSTOMER Please fill in before you continue. The following information is necessary when calling CEECO for assistance. MODEL NUMBER MODEL IP-HOB-531-X OR SSP-511-X EQUIPPED WITH SPK1.07r1 FIRMWARE. SERIAL NUMBER DATE MANUFACTURED LOCATION INSTALLED For us to better serve you, please have this information available when calling for technical support.
ISSUE 4.0 TABLE OF CONTENTS SECTION PAGE 1.0 INTRODUCTION................................................................................................. 4 2.0 GENERAL ............................................................................................................. 4 3.0 PROGRAMMING ................................................................................................ 5 PROGRAMMING CONTINUED .......................................................................
ISSUE 4.0 1.0 INTRODUCTION The practices in this manual provide installation and maintenance information for the CEECO Voice Over Internet Protocol (VoIP) Model IP-HOB-531-X Hands free Weather Resistant Telephone or Model IP-SSP-511-X Stainless Steel Panel Telephone, equipped with SPK1.07r1 firmware. The information in this manual is subject to change without notification.
ISSUE 4.0 3.0 PROGRAMMING 3.1 Remove the front stainless steel panel by loosening the four security screws with a security tool (sold separately) and remove them. Remove the panel and attached telephone assembly. 3.2 Connect the telephone to a working telephone line or a DTMF test set. 3.2 Locate the pair of plastic mini-jumpers located near the edge of the printed circuit board. Move them to the “ON” or innermost position, as depicted on the last page of this manual. 3.
ISSUE 4.0 PROGRAMMING CONTINUED LOCATION #00 Digit 1: Always 0 for this model. Digit 2: 0 No incoming calls allowed. 1 Incoming calls allowed. Digit 3: 0 No time-out disconnect 1-9 Minutes time-out disconnect Digit 4: Always 0 for this model Digit 5: Always 1 for this model Digit 6: Always 0 for this model. Digit 7: Always 0 for this model Digit 8: Always 0 for this model Digit 9: Always 0 for this model Digit 10: 0 0 No wink detect. 1-9 Length of the wink detect. (1=50ms incremental to 450 ms.
ISSUE 4.0 PROGRAMMING CONTINUED 3.9 3.10 4.0 When you are finished programming, press the “CALL & HANGUP” button to hang up the phone. Return the two plastic mini-jumpers to the “OFF” or outermost position, as depicted on the last page of this manual. Secure the telephone assembly in the housing. The phone is now ready for use. Refer to the INSTALLATION NOTES section ahead for details regarding the VoIP configuration setup prior to proceeding.
ISSUE 4.0 6.0 INSTALLATION NOTES AND ASSEMBLY INSTRUCTIONS 6.1 Using a 301-064 security tool (sold separately) loosen and remove the security screws. 6.2 The security tool is for a standard 5/32" button head screw generally used on the framework of the phone booths. 6.3 Separate the faceplate assembly from the weather resistant housing or mounting by pulling the faceplate forward. The mounting box is designed to be mounted flush with a flat vertical surface.
ISSUE 4.0 *****WARNING***** A. B. Never install telephone wiring during a lightning storm. The telephone must be grounded in accordance with local and national electric codes. Never install telephone jacks in wet locations unless the jack is specifically designed for wet locations. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. Use caution when installing or modifying telephone lines. C. D. E. 7.
ISSUE 4.0 8.0 SPECIFICATIONS INPUT POWER: ATA powered LOOP CURRENT: 35 mA minimum 80 mA maximum IMPEDANCE: 600 ohms SIGNALING: Manual on-off hook ENVIRONMENTAL: Temperature 0o C to 50o C Humidity 20%-90% non-condensating PROGRAMMING: Via DTMF keypad. MEMORY RETENTION: Non-volatile memory retention DIMENSIONS: (SSP) 7 1/6 wide x 11 1/4 high x 4 1/4 deep MOUNTING: Vertical surface mount. WEIGHT: Approximately 4 lb. DIMENSIONS: (HOB) 11.28" high x 7.
ISSUE 4.0 9.0 PARTS LIST QUANTITY PART NUMBER DESCRIPTION 4 331-006 OUTER COVER SECURITY SCREW 1 301-018 MODULAR LINE CORD 1 531-11075 FACE PLATE 1 700-008 KEYPAD CABLE 1 660-000 CEECO SPEAKER BOARD 1 705-110 CONNECTORIZED KEYPAD 1 14067 1 6020 1 14024 1 HOB-331 Open-faced weather-resistant enclosure 1 331-010 STAINLESS STEEL PANEL. 1 401-009 RINGER 1 N/A 1 MICROPHONE.
ISSUE 4.0 10.0 FCC NOTICE 10.1 FCC REGISTRATION AND REPAIR INFORMATION Your new telephone has been registered with the Federal Communication Commission (FCC) in accordance with Part 68 of its rules. The FCC requires that you be advised of certain requirements involving the use of this telephone. 10.
ISSUE 4.0 11.0 REPAIR AND RETURN INFORMATION 11.1 WARRANTY REPAIR Any device returned requiring warranty service, repair or credit must be accompanied with a "Return Material Authorization" (RMA) FORM. It must include: return-shipping instructions, original purchase order number and special marking instruction. A description of the trouble observed must be attached to the defective unit. This information must be inside the shipping container. 11.
ISSUE 4.0 12.0 WARRANTY POLICY 12.1 GENERAL CEECO products are guaranteed to be free of defects in material and workmanship for a period of 365 days from the date of original purchase. CEECO's obligation under this warranty is limited to repair or replacement of any part found to be defective by CEECO. Under no circumstances shall CEECO be liable for loss, damage, cost of repair or consequential damages of any kind, which have been caused by neglect, acts of God, abuse or improper operation of equipment.
ISSUE 4.0 13.0 DIAGRAM Locate the mini jumpers on the corner of the PCB. O N O MOVE THE MINI JUMPERS TO THE ON POSITION BEFORE GOING OFFHOOK. When programming is completed, move the mini jumpers to the OFF position. O FF N O O FF N O FF NOTE: Do not leave the mini jumpers in the ON position, this will decrease battery life.
