Instructions / Assembly

1
702 Interchange Blvd, Newark DE, 19711, USA
Pre Installation
PLANNING INSTALLATION
□ Read all instructions before installation.
□ To avoid damaging this product, assemble it on a soft, non abrasive surface, such as carpet or cardboard.
□ Keep your receipt and these instructions for proof of purchase.
Safety Information
□ Consult a qualified electrician if you have any
electrical questions.
CAUTION:
WARNING:
3-Light Vanity Fixture
USE AND CARE GUIDE
Model#: 417305
Safety
glasses
Electrical
tape
Phillips
screwdriver
Flat blade
screwdriver
Pliers
Wire
strippers
2
702 Interchange Blvd, Newark DE, 19711, USA
Pre-installation (continued)
PACKAGE CONTENTS
Part Description Quantity
A
B
Light fixture
Glass Shade
1
3
HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.
Part Description Quantity
AA Mounting unit 1
BB Mounting screw 2
CC Wire Nut 3
DD
EE
Cap nut
Steel ring (pre-installed with light fixture)
2
3
TOOLS REQUIRED
Ladder
3
702 Interchange Blvd, Newark DE, 19711, USA
Installation
2
1
Making the electrical connections
TURNING THE LIGHT ON
□ Connect the copper wire from the fixture body (A) to the
mounting unit (AA) by securing it with the pre-installed
ground screw.
□ Connect the black wire from the fixture to the black wire from
the outlet box, the white wire from the fixture to the white
wire from the outlet box, and the copper wire from the fixture to
the ground wire from the outlet box with the wire nuts (CC).
Secure with electrical tape (not included).
1
Attaching the mounting unit to the
junction box.
4
installing the shade and bulbs
3
Securing the light fixture
□ Place the mounting bracket (AA) over the outlet
box (not included) so that the holes on the
mounting bracket (AA)align with the screw holes
on the outlet box.
□ Screw the outlet box screws (BB) through the
holes on the mounting bracket (AA) into the screw
holes on the outlet box.
□ After wires are connected, tuck them carefully
inside the junction box.
□ Secure the light fixture (A) to the junction box by
placing it over the pre-installed support screws on
the mounting unit (AA) and securing it with the cap
nuts (DD).
□ Remove the pre-installed steel rings (EE) from the light
fxture (A), add the glass shades (B) and re-secure the
steel rings (EE).
□ Install three 60-watt max. medium-base incandescent
bulbs(not included).
4
702 Interchange Blvd, Newark DE, 19711, USA
Operation
□
Turn the light switch on to activate the fixture.
Care and Cleaning
□ Clean the lamp with a soft, dry cloth.
□ Do not use any cleaners with chemicals, solvents, or harsh abrasives.
Troubleshooting
Problem Possible Cause Solution
The bulb is burned out. Replace the light bulb.
The power is off.
There is a faulty wire connection.
Ensure the power supply is On.
The circuit breaker is off.
Check the wiring.
Ensure the circuit breaker is in the On position.
The fuse blows or circuit breaker
trips when the light is turned on.
There are crossed wires or the
power wire is grounding out.
Check the wire connections.
C
the Customer Service Team.
ontact a qualifed electrician or contact
The bulb will not light.
Inspect the wire insulation for any cuts,
abrasions, or exposed copper that may have resulted during
shipping. If there is a defect in the wire, do not attempt
installation. Please call our Customer Service Team.
Before starting installation of this fixuture
or removal of a previous fixtu re, disconnect the power
by turning off the circuit breaker or by removing the
fuse at the fuse box.
The pre-installed screws on the mounting
unit(AA) should protrude out away from the junction box.
NOTE:
If the wires from the fixture are the same color,
attach the side with markings or letters to the black
(positive) wire and the other to the white (neutral) wire.
NOTE:
___________BB___________AA ___________CC
___________DD ___________EE
A
B
AA
BB
4. Secure the light fixture (
box by placing it over the p
screws on the mounting u
CC
A
DD
EE
A
B