Instructions / Assembly

mm
THIRD
ANGLE
PROJECTION
V1.0
审 核：
制 图：
批 准：
日 期：
页 次：
1/1
3.508.00391
物料编码：
产品名称：
版 本：
材 质：
单 位：
深圳市博为光电股份有限公司
圆形UFO说明书
刘启立
基本尺寸
0~30
30~80
80~315
315~700
700~1300
1.0
1.5
2.0
2.5
3.0
1300~2500
4.0
公 差
MM MM
更改内容
新建V1.0
版本
尺寸：210*297mm 70G书纸，中间对折
单黑色正反面印刷，外框线为刀模线
更改时间
PRE-INSTALLATION
● Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts
with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to
assemble, install or operate the product. Contact customer service for replacement parts.
● Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape,
Wire Cutters, Safety Glasses, Ladder, Wire Stripper, electric drill, etc.
CARE AND MAINTENANCE
Caution: Before attempting to clean the fixture, disconnect the power to the fixture by turning the breaker off
or removing the fuse from the fuse box. This LED light fixture is made from quality materials that will last many
years with minimum care and maintenance. You may want to clean the fixture with a soft cloth periodically.
To maintain the best appearance of the fixture, do not use cleaners with chemicals, solvents or harsh abrasivers.
Do not use liquid cleaner on the LEDs, LED driver, or wiring inside the light fixture.
Read All Instructions. SAVE THESE INSTRUCTIONS
SAFETY INFORMATION
Please read and understand this entire manual before
attempting to assemble, operate or install the product.
WARNING
● Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse
or switching off circuit breaker.
● Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires
to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could
cause serious injury or death from electric shock.
● LED electronics can be damaged by electro static discharge (ESD) shock. Before installation, discharge
yourself by touching a grounded bare metal surface to remove this hazard. To avoid damage, do not touch
the LED module.
CAUTION
● All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
● Contact your municipal building department to learn about your local codes, permits and/or inspections.
● Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC.Consult a qualified
electrician before installation.
● Do not connect this fixture to an electrical system that does not provide a means for equipment grounding.
Never use a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a
grounding means, do not attempt to install this fixture. Contact a qualified, licensed electrician for information
with regards to proper grounding methods as required by the local electrical code in your area.
● If a dimmer control switch is used with this fixture, obtain professional advice to determine the correct type
and electrical rating required.
PROBLEM
Light will not come on.
Cable does not connect.
A. Fixture not properly connected.
B. Light bulbs not working.
C. Fixture not receiving power.
A. Correct end of cable not matched
with correct end of light.
A. Check wires to ensure proper connections.
B. Replace light bulbs.
C. Check to make sure breaker is on and test another
working electrical device to make sure it is receiving
power.
A. Check markings on cable and light to ensure proper
pairing.
POSSIBLE CAUSE SOLUTION
FCC WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
NOTES:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy ,
and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
TROUBLE SHOOTING
UFO HIGH BAY Installation Instructions
Pendant Mounted
Suspended Mounted
INSTALLATION