Technical Specifications

Page 2 of 2 August 2016
Impact Resistance (ASTM D4226):
60in-lbf (Procedure A, H.25)
Weatherability (ASTM D3679): No surface or structural defects
such as peeling, cracking, chipping.
Coefficient of Linear Expansion (ASTM D3679):
3.00 x 10
-5
in/in
0
F / 5.10 x 10
-5
cm/cm
0
C
Gloss (ASTM D3679): plus or minus 8 units
Surface Distortion (ASTM D3679): No distortion at 120
0
F
Windload Resistance (ASTM D 5206):
Wind speed up to 161 mph
Design Pressure up to -61 psf
E. Siding Dimensions and Description: (Select Profile)
Cedar Creek Double 4 Dutch Lap: Double 4 Dutch Lap profile
with Single Nail Hem horizontal siding panel, 8 in. wide exposure
configured as two 4 in. panels, 12ft-6in. length.
Cedar Creek Double 4 Clapboard Lap: Double 4” Lap profile with
Single Nail Hem, horizontal siding panel, 8 in. wide exposure
configured as two 4 in. panels, 12 ft 6 in length.
Cedar Creek Double 5” Dutch Lap: Double 5” Dutch Lap profile
with Single Nail Hem, horizontal siding panel, 10 in. wide exposure
configured as two 5 in. panels, 12ft. length.
Cedar Creek Double 5” Clapboard: Double 5” Lap profile with
Single Nail Hem, horizontal siding panel, 10 in. wide exposure
configured as two 5 in. panels, 12ft. length.
F. Siding Panel Description:
Thickness: (0.040 in. ±0.001 in.) with Single Nail Hem
Embossing/Woodgrain: Siding panel to match the sample provided
under section 1.03.
Color: Siding color shall be present throughout the thickness of the
panel. Panels shall be produced using ABTCO’s exclusive Ultra-
Vinyl formulation. Siding color shall be as specified by architect.
Interlock: Siding panels are made with post form style lock with
positive interlock. Both ends of the panel are factory cut and
notched for overlap.
Nail Slots: Elongated nail slots 1" long are spaced approximately
1/2" apart in the nailing hem to allow siding to expand and contract
properly.
Weep Holes: Small holes under the bottom butt prevent vapor build
up and allow accumulated moisture to escape.
2.01 Accessories:
A. Accessories shall be consistent with the shape, size and properties
as shown in the drawing and as required for complete installation.
Color shall be matched or color coordinated to the siding according
the architect's specifications.
Accessories shall be produced from the same compound materials
and with comparable properties as the siding.
2.02 Fasteners:
A. Galvanized nails or other corrosion-resistant fasteners, as
recommended by manufacturer for specific application shall be
used to install the siding.
PART 3 – EXECUTION
3.01 Examination
A. Confirm that all critical dimensions are as specified in the drawings.
B. Commencement of siding installation implies acceptance of the
substrate as suitable to accept siding.
3.02 Preparation
A. Any substrate flaws or defects must be repaired, and free from
obstructions before the vinyl siding is applied.
3.03 Installation
A. Solid sheathing and a weather resistive barrier shall be provided
behind the siding, as required by the applicable code.
B. Siding is installed with nails driven into furring strips or wall studs
spaced not more than 16 in. on center. The siding fasteners are
corrosion resistant nails with a minimum 11/32 in. diameter head
and a 0.135 diameter shank.
C. Nails shall be long enough to penetrate the nailing base by at
least 7/8 in.
D. Install in accordance with the latest edition of the "Vinyl Siding
Installation Manual" published by the Vinyl Siding Institute.
E. The vinyl siding and accessories shall be installed in accordance
with the best practice. Nails shall be centered in the siding nail
slots with a minimum 1/16 in. clearance between the back of the
nail head and the face of the siding. Nails shall be driven
perpendicular to the substrate.
F. At all openings and stops, a minimum gap 1/4 in., shall be
provided for expansion and contraction. Joints between panels
shall be overlapped a minimum of 1 in., with all joint members
plumb and true.
3.04 Field Quality Control
A. After installation of siding check entire surface for obvious flaws
or defects. Replace and repair any problem areas.
3.05 Cleaning
A. After the vinyl siding has been applied, clean as necessary to
remove all fingerprints and soiled areas.
B. Clean and remove all scrap, packaging and unused materials
resulting from the installation of vinyl products.
All ABTCO Vinyl Sidings and accessories are backed by a Lifetime
Limited Warranty.