ICED TEA BREWER Model: TB-3P (Manual Pour0ver) POUROVER OPENING POWER SWITCH READY LIGHT BREW FUNNEL S.S. BREW COVER 3 GALLON S.S.
LARGE FUNNEL WITH STANDARD RIM USED ON TB-3 AND TB-5 PART NO V211R FUNNEL BRUSH X128A FAUCET BRUSH X159A DRIP TRAY
ELECTRICAL SPECIFICATIONS DESCRIPTION VOLTS PHASE HZ WATTS KW NO. OF HEATERS AMPS RECEPTACLE NEMA NO. TB-3 3 GAL Brewer W/ B-1/3T 120 1 60 1.8 1 15 5-15R TB-5 5 GAL Brewer W/ B-1/5T 120 1 60 1.8 1 15 5-15R TB-3P Pour-Over Brewer 120 1 60 1.6 1 15 5-15R B-1/3 3 GAL Dispenser & Base - - - - - - - - - - - - - - - - - - - - - - - - - - - - MODEL NO.
The brewer must be connected to a cold water supply with an operating pressure of 20psi minimum and 90psi maximum from a ½ in. supply line. If pressure should exceed 90psi, install a pressure regulator to reduce the operating pressure to 50psi. Use ¼ inch copper tubing for installation of less then 25 ft. and 3/8 copper tubing for more then 25ft from a ½ in cold water supply line. Install the water inlet fitting provided onto the inlet valve located in the back of the unit. Do not over-tighten.
FLAVOR CHART Model No. Type of Tea HOT WATER Brewing Concentrate COLD WATER Dilution TEA BAG SIZE Totat Brew Time unsweet 0.75 gal. (96 oz) in 3 minutes 2.25 gal. (288 oz) 3 oz 6.0 min sweet 0.70 gal. (90 oz) in 3 minutes 2.00 gal. (256 oz) 3 oz 5.5 min. unsweet 1.30 gal. (166 oz) in 5 minutes 3.70 gal. (473 oz) 4 oz 8.0 min sweet 1.20 gal. (153 oz) in 5 minutes 3.00 gal. (384 oz) 4 oz 7.0 min TB-3 TB-5 Tea Brewing Instructions CAUTION: Operate with care.
TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock, unplug the power cord before repairing or replacing any internal components. Before any attempt to replace a component be sure to check all electrical connections for proper contact. PROBLEM PROBABLE CAUSE REMEDY 1 Brewed Cold Tea. a) Heater Switch OFF. b) Run out of hot water c) Thermostat is OFF. d) Loose electrical connection. e) Thermostat is defective. f) Hi-Limit Temperature Switch is tripped.
HOT WATER TANK Part No.RV33C 3.
ADJUSTMENTS TO BE PERFORMED BY QUALIFIED SERVICE PERSONNEL ONLY. Caution: Brewer should be unplugged from electrical outlet before any service is performed. The water flow rate coming from the hot water tank is constant/fixed at 0.75 gal/min. Increasing or decreasing the amount of hot water dispensed from tank can also be used to adjust the strength of the tea. L265A BREW TIMER The Longer water flows - More water - Weaker tea; Less water flows - Less water - Stronger tea.
5. DUAL WATER INLET VALVE: The Water Inlet Valve is located on the lower part of the main body with the threaded end protruding out of in the back. The Water Inlet Valve allows water flow up to .87 gal./min. [gpm]. One side supplies water to the tank and one side supplies water directly to the Iced Tea dilution water nozzle. The time that each side draws water is controlled by the Hot Water timer and Cold Water Timer. CD241 WATER INLET VALVE 6.
BACKFLOW PREVENTION CHECK VALVE PROVIDED AND INSTALLED BY CUSTOMER CRITICAL COMPONENTS TESTS A) Water Inlet Valve Test Check hot water side, going to tank: Turn power off. If the water level rises inside the tank, the Water Inlet Valve is leaking. Disconnect wires from the Water Inlet Valve coil and connect a 2 wire line cord to the terminals. Plug it into electrical outlet. If water flows in and stops when you pull it out, the Valve is working fine. Repeat this test a few times.
B-1/3 (3 GALLON) B-1/5 (5 GALLON) RX62A - RY02A RX62A - RY72A Q184A M028A P264A M776A Q184Q Q190A (R021A) M776Q M028A P264A M777A Q181A Q190Q M777Q Q182A Q181Q M632A (2) P015A (2) M632A (2) P015A (2) LABEL CHROME D064A RT34A LABEL CHROME D064A D025S 19015 (2) K105A RT31A Q182Q B1/3 3 GAL OCTAGON BASE RT33A D025S 19015 (2) K105A RW47A RT31Q RT34A B1/5 5 GAL OCTAGON BASE RT33A RT33Q RT33Q RW47Q
INSTALLATION AND OPERATING INSTRUCTIONS MODEL: TB-3P MANUAL POUR-OVER BREWER WARNING: MACHINE WARRANTY IS VOID IF CONNECTED TO ANY VOLTAGE OTHER THAN 120 VOLTS. NOTE: A dedicated 120 Volt, 15-Ampere Grounded Outlet should be supplied for each unit installed. Check local codes for compliance installation. The TB-3P is a Manual Pour-over Brewer and therefore is NOT equipped with water inlet connection. Items shipped with Brewer: ½ Gal. Pitcher, 4” legs, drip tray and Instruction Manual.
TO BREW: 1. Place the 3 Gallon Tea Dispenser, with Brew-thru Cover, onto the base of the Brewer with the hole in the cover positioned under the brew funnel. 2. Place 3 oz. Tea Bag on brew funnel platform, and insert into brewer. 3. Pour two ½ Gallon Pitchers of Cold Tap Water through the screened top opening. 4. When the green Brew Light goes out and the funnel stops dripping (approx.
TROUBLE SHOOTING GUIDE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit.. Before any attempt to replace a component be sure to check all electrical connections for proper contact PROBLEM PROBABLE CAUSE REMEDY 1 Brewer Does Not Brew No power at outlet Circuit Breaker tripped due to overloaded outlet.
