Mechanical Specifications MODEL: Width Depth Height Hoppers In In In Qty Hoppers Lb. Tank US Gal. Burst Capacity Lit Display Area Shipping (W X H) Sq. In. Weight Lb. GB1M-LD SPACE SAVER 8½ 22 31 ½ 1 8 SQ 2 58 (7 x 13) 91 65 GB2M-5.5-LD GB3M-5.5-LD GB3M-10-LD SPACE SAVER 8½ 11 11 ½ 22 22 22 34 34 34 2 2.75 2.75 58 85 112 (7 x 13) 91 (9½ x 13) 123 (123/8 x 13) 164 86 100 110 14 1/8 17 17 22 22 22 34 34 34 5½ 4 5½ 10 P 5½ 5½ 5½ 10 P 4 4 4 4 10 5½ 4 4 4 2.
INSTALLATION INSTRUCTIONS Water Inlet Connection: This equipment is to be installed to comply with the applicable Federal, State, or local plumbing codes having jurisdiction. In addition: 1. A quick disconnect water connection or enough extra coiled tubing (at least 2x the depth of the unit) so that the machine can be moved for cleaning underneath. 2. An approved back flow prevention device, such as a double check valve to be installed between the machine and the water supply.
UNPACKING INSTRUCTIONS Carefully unpack the GB Machine and inspect immediately for shipping damage. Your GB Machine was shipped in a carton designed to give it maximum protection in normal handling. It was thoroughly inspected before leaving the factory. In case of damage, contact the shipper, not Cecilware. DESCRIPTION AND LOCATION OF COMPONENTS Note: Refer to Illustration A for description and location of COMPONENTS and CONTROLS. 1. HOPPERS.
Model L690A (Rev. B) Dual Probe Liquid Level Controller Overview - The L690A is a Dual Probe Liquid Level Controller designed to maintain a specific level of water in the tank. This device utilizes two level probes for increased reliability. Independent maximum fill timers are incorporated in the controller for overflow protection. Operation - When a fill problem occurs, the Dual Probe Liquid Level Controller turns OFF power to the fill valves and remains OFF until the power input is reset (i.e.
TROUBLESHOOTING GUIDE WARNING: To reduce the risk of electrical shock unplug the dispenser power cord before repairing or replacing any internal components of the unit.. Before any attempt to replace a component be sure to check all electrical connections for proper contact. PROBLEM PROBABLE CAUSE REMEDY 1 A Dispensing unit unplugged Reconnect dispensing unit Light Display B No power from Terminal Block Check the Terminal Block for loose wire not lit. C Defective Bulb Replace Bulb. No power.
SANITIZING: All sanitizing agents in the food zone must comply with 21 CFR 178.1010. All food dispensing units should be sanitized periodically. All parts to be sanitized must be cleaned first. To prepare a sanitizing solution: ADD 2 TSP. OF LIQUID CLOROX BLEACH (5.25% CONCENTRATION) TO 1 GALLON OF WATER AT ROOM TEMPERATURE (70°90°F). Note: Always start with a unopened bottle of Clorox Bleach since the solution from an opened bottle has a short life span. • Soak all parts for a minimum of 3 min.
12
14
15
16
17
18
ITEM DESCRIPTION 1 GB-LP TANK ASS’Y/TANK TOP ASS’Y -SEE METAL PARTS LIST – NEXT PAGE Å Å Å M326A M326A M326A ------- M324A M326A L463A K178A CD257 ------C032S 60105 ----L690A -------B129A CD56A CD224 CD214 M172A Å L069A C002A Å Å CD75A CD124 CD66A CD65A M379A CD64A M467A CD63A CD137 CD61A M378A CD67A L455A ---B216A CE82A CB04A ------M367A Å N978A ---------- M324A M326A L463A K178A CD257 ------C032S 60105 L533A L690A -------B129A CD56A CD224 CD214 M042A Å L069A C002A Å Å CD75A CD124 CD66A CD65A M3
METAL PARTS LIST MODELS ITEM 1 ITEM 23 ITEM 23 TANK ASS’Y GRILL SC35C TANK TOP ASS’Y SC32C RI23A RI11A RD03Q RH91A GB2M-5.5 SC35C SC32C RI18A RI11A RH47Q RG48A GB3M-5.5 SC36C RI39C RI19A RI12A RH48Q RG48A GB4M-5.5 RL72C RL69C RI20A RH05A RH49Q RG48A GB5M-5.
21
22
23
24
25
26
27
28
29
30
31
32
33
