User Guide

ManualsBrandsCecilware ManualsOtherFE-100G

AUTOMATIC GAS

COFFEE URN

OPERATION MANUAL

MODEL:

FE-100G

SPECIFICATIONS

INSTALLATION

MAINTENANCE TIPS

REPAIR PARTS LIST

WIRING DIAGRAMS

GAS SPECIFICATIONS

MODEL NO. NATURAL GAS

BTU/HR @ 3.5” W.C.

PROPANE GAS

BTU/HR @ 10” W.C.

FE-100G 32,000 32,000

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND

LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE.

THIS INSTALLATION MUST CONFORM WITH THE NATIONAL FUEL GAS CODE,

ANSI Z223.1 (LATEST EDITION).

WARNING: IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE

OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ

THE INSTALLATION, OPERATING AND MAINTENANCE INSTRUCTIONS

THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT.

CECILWARE CORPORATION

43-05 20

AVENUE, LONG ISLAND CITY, NY 11105-1295

• 718 932-1414

N529A 08/99 DS

Summary of content (11 pages)

PAGE 1
AUTOMATIC GAS COFFEE URN OPERATION MANUAL MODEL: FE-100G SPECIFICATIONS INSTALLATION MAINTENANCE TIPS REPAIR PARTS LIST WIRING DIAGRAMS GAS SPECIFICATIONS MODEL NO. FE-100G NATURAL GAS BTU/HR @ 3.5” W.C. 32,000 PROPANE GAS BTU/HR @ 10” W.C. 32,000 FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE. THIS INSTALLATION MUST CONFORM WITH THE NATIONAL FUEL GAS CODE, ANSI Z223.1 (LATEST EDITION).
PAGE 2
SAFETY PRECAUTIONS FOR YOUR SAFETY, THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE FOLLOWED AND ENFORCED. IF YOU SMELL GAS: • OPEN WINDOWS • DON’T TOUCH ELECTRICAL SWITCHES • EXTINGUISH OPEN FLAMES • IMMEDIATELY CALL YOUR GAS SUPPLIER 1. Instructions must be posted in a prominent location and all safety precautions taken in the event the user smells gas. Obtain this information from your local gas supplier. 2. LIGHTING: Follow the instruction on page 6 and label attached to right side of coffee urn. 3.
PAGE 3
FE-1 0 0 G AUTOM ATIC COFFEE URN FE-100G AUTOMATIC COFFEE URN Dimensions Body Overall Overall Overall (inch) Depth Depth Height Width 16.0 19.5 31.0 37.0 Water ¼” Copper tubing connection Construction Type 304 18-8 Stainless Steel Shipping Wt. 125 lb.
PAGE 4
AIR SUPPLY AND VENTILATION: Adequate ventilation and air supply must be provided in order for the coffee urn to operate properly and efficiently. The area in front of and above the unit must be clear to avoid any obstruction of flow of combustion and ventilation air. DO NOT under any circumstances, connect the coffee urn flue directly to a building exhaust system or place the flue outlet directly into the plenum of the exhaust hood as it will adversely affect the gas combustion of the coffee urn.
PAGE 5
FE-1 0 0G AUTOM ATI C GAS COFFE URN PARTS LIST FOR FE-100G GAS SYSTEM NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 DESCRIPTION SIDE BOX DOOR SIDE BOX WASHER 2" HEX BUSHING 3/4 X 3/8 NPT SPACER 1/4" GAS VALVE R/S 7000MVRLC 3/8 NPT 4" NIPPLE, BLACK 1/4 COMP FITTING 1/4 ALUM PILOT TUBE 3/8 X 3/8 NPT L COMP FITTING 3/8 ALUM GAS VALVE TUBE THERMOSTAT RX-2051-12 WIRING HARNESS 8-32 HEX NUT #10 STAR WASHER 8-32 X 3/4" WELD STUD THERMOPILE PILOT ASSEMBLY ORIFICE,NAT ORIFICE, LP BURNER MANIFOLD 8-32
PAGE 6
RELIGHTING: Shut off all gas and wait approximately 3 minutes before relighting the pilot. SHUTTING DOWN: For temporary shut down, turn the thermostat to lowest or OFF position; then turn gas cock dial to PILOT position. To shut boiler down completely, partially depress and turn gas cock dial to OFF position. CORRECT PROCEDURES FOR BREWING COFFEE AS RECOMMENDED BY THE COFFEE BREWING CENTER • • • • • • Use fresh or drip grind coffee, spread evenly, as an even coffee bed is important for proper extraction.
PAGE 7
adjustment slot and turn it counter-clockwise to increase or clockwise to decrease by-pass flow. At the completion of the brewing cycle, measure the volume of the water in the coffee liner. The timer may have to be readjusted to obtain the correct volume of water. The proper setting of the by-pass will have to be determined by the user. THERMOSTAT: To adjust the temperature of the water in the urn, turn the thermostat knob to “10”and remove the knob without moving the thermostat shaft.
PAGE 8
• REPLACING SOLENOID VALVE. 1. Shut off water supply and remove fuse () from front panel. 2. Disconnect wires from terminals on solenoid coil. 3. Remove flare nut from solenoid valve and unscrew valve solenoid from bracket. 4. Install new unit. • REPLACING FLOAT SWITCH. 1. Remove fuse () from front panel. 2. Remove screws from timer panel and remove timer exposing terminal board and electrical wiring. 3. Disconnect wires from terminals () and () on terminal board and release float switch wires (see ill.
PAGE 9
3. Open the control box and disconnect the two pump wires from the quick disconnect terminals. 4. Loosen union fittings on pump and remove pump from urn. 5. Replace pump and follow priming instruction. NOTE: Pump and motor assembly is factory lubricated for the life of the pump. • TIMER SOLID-STATE Depress BREW button, hold for approximately 10 seconds, and then release.
PAGE 10
PARTS LIST ME-10/15G NO 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 DESCRIPTION KNOB COVER BODY GAUGE SHIELD MTG BRACKET VENT CAP ASSEMBLY GAUGE SHIELD WASHER KIT WATER GAUGE GLASS WATER GAUGE SHIELD DIAL THERMOMETER CHROME PLATED NUT 3/8" NPT OVERFLOW TUBE HANDLE BONNET FAUCET SPRING SS STEM CUP SEAT FAUCET SHANK OVERFLOW DRAIN BURNER SUPPORT BRACKET LEGS SET OF 4 T-BURNER PILOT SUPPORT BRACKET PILOT ASSEMBLY,
PAGE 11
51 52 53 54 55 56 SILICONE GASKET STEM VALVE ADAPTER 1/4-20 FLOAT, SS 3" LP CONVERSION KIT WATER GAUGE ASSEMBLY FAUCET ASSEMBLY M256A M0251 M0589 M0892 L347P D017A 11 M256A M0251 M0589 M0892 L347P D020A D017A