WC600 Integrated Dishwasher Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Availability of this manual in an alternative format: A soft copy of this manual is available for download from www.cda.eu. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services. Disposing of a household appliance separately avoids possible negative consequences for the environment and health.
sharp objects such as knives are placed blade down to prevent accidents. • Do not open the dishwasher door when a programme is running. If it is necessary to do so, then open it only slightly to allow the dishwasher to pause the programme and prevent any water spilling out. Remember that the water in the dishwasher can be very hot when the programme is running. • When the dishwasher is not in use, we reccomend that you turn off the water supply at the supply tap and disconnect the main supply.
Recommendations • To reduce energy and water consumption, remove all dirt residues from the dishes prior to loading the dishwasher. • Only run the dishwasher when fully loaded. • Place hollow items (bowls, glasses and pans) face down in the basket. • Do not put dishes or cutlery with tobacco ash, wax, lubricating grease or paint residues in the dishwasher. Before First Use • Set the water softener level as required by the water hardness in the area.
Control Panel P P Fig. 1 Power button (1) • To switch the dishwasher on or off, press the power button (1). When you switch on the dishwasher, the end of programme light will illuminate, and two dashes will appear on the display. The interior light will work automatically when the dishwasher is switched on. Programme display (2) The programme display shows the selected programme and the remaining time to run. If there is a fault on the dishwasher, the fault code will show on the display.
Delay timer button (4) The dishwasher is equipped with a variable timer of up to 19 hours’ duration at hourly intervals. • To set the delay timer, press the delay timer button (4). This will switch the timer on for one hour. • To change the delay duration, press the delay timer button again until the required delay duration is shown on the display, alternating with the selected programme and the programme duration.
The prewash is also an independent programme (8) which can be used to rinse the contents of the dishwasher, for example if the dishwasher is not yet full and a complete programme is not yet required. • To do so, select the programme as described below. • To select the Intensive+ 70º programme, select the prewash function with the Intensive 60º programme.
Starting a programme • Press the Power button (the end of programme light will be switched on) • Press the Programme Selection button until the required programme is shown on the display. • If required, set the delay timer by pressing the Delay Timer button • Once a programme is selected, the end of programme light will switch off. • When you close the dishwasher door, the programme will start automatically. Please note: The dishwasher stores the most recently used programme in its memory.
At the end of a programme If possible, do not open the dishwasher door once the programme has started. At the end of a programme, the dishwasher will beep five times, and the end of Programme Indicator light will switch on. Changing a programme It is possible to change the programme if necessary once the programme has started. • First open the door slightly to reduce the risk of water spillage. • Press the programme selection button until the required programme is shown on the display.
Control Panel Cancelling a programme It is possible to cancel the programme once is has started. • First open the door slightly to reduce the risk of water spillage. • Press and hold in the Programme Selection button until the end of programme indicator flashes and a “1” shows on the display. • Then close the door. The dishwasher will run a drain cycle which will take approximately 30 seconds. Once this is complete, the dishwasher will beep five times and the end of programme light will switch on.
Interior Light The dishwasher is equipped with an interior light to illuminate the dishwasher when loading and unloading. This light is preset to Eco mode when supplied, but can be adjusted if necessary. To select the normal interior light mode: • Open the door and press the Power button (1) to switch the dishwasher on. • Press and hold the 3 in 1 (5) and Prewash (6) buttons for three seconds. • The display will show IL0 for two seconds to show normal mode is set.
Detergent To fill the detergent compartment 1. Push the latch to open the compartment. 2. Add the required amount of Fig. 2 detergent. The main detergent compartment “b” (figure 2) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, to be used depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment “a” (figure 1). 3.
If you do use combination detergents, add salt and rinse aid to the dishwasher and then adjust the water hardness setting and rinse aid setting to the minimum. When you then use separate detergents again, you should fill the salt and rinse aid compartments, adjust the water hardness setting to the maximum and run an empty wash, then adjust the water hardness setting and the rinse aid setting to the appropriate level.
detergent into the prewash section of the compartment “a” (figure 2). 3. Then close the detergent compartment lid until the latch locks. Detergent Please note: You should only use detergents designed specifically for fig 1 in dishwashers. To use fill the detergent compartment 3. Replace the cap and the lower basket. 1. Push the latch as shown in figure 1. using dishwasher tablets, always use the detergent 2. IfAdd the required amount of detergent.
Softener Adjustment The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or alternatively contact your local water board. fig. 5 1. Open the testing strip (figure 5). 2.
If the hardness of the water you use is above 63 dE or if you are using well water; you are recommended to contact your local water board to confirm the water hardness level and to use filter and water refinement devices. Please note: The level of water hardness is preset to level 3. 1. Press and hold down the programme selection button 2. Press the Power button to switch on the dishwasher 3. Keep the programme selection button pressed until “SL” shows on the display and then disappears 4.
id Rinse ecompartment aidAid compartment se Aid aidrinse compartment by turning andaid removing the the cap cap as as To fill the rinse compartment rinse aidaid compartment by turning and removing the compartment e 4. figure pen the4.rinse by turning andcompartment removing the cap as 1. aid Ocompartment pen the rinse aid down the rinse aid indicator goesgoes dark, in compartment figure 4.
Dishwasher Baskets Top basket height adjustment while it Basket your ma top bask Basket height adjustment mechanism on the top basket of Basket height adjustment mechanism on the top basket of your machine is designed to let you adjust the height of you your machine is designed to let you adjust the height of your top basket upwards or downwards, withoutyour removing ma it from top basket upwards or downwards, without removing it from your machine when it is full, and create large spaces at the your machi
Adjustable cup racks The dishwasher is equipped with adjustable cup racks on the middle basket to allow long stemmed glasses to rest securely during washing, or stacking of smaller cups. The cup racks can also be folded up when not required to allow more space for larger items. Folding racks in middle and lower basket The dishwasher is equipped with folding plate racks for the middle and lower baskets to offer the option of different uses of space as shown in fig. 11.
Standard Loading and Test Data Capacity • Middle and lower baskets: 15 place settings. • The middle basket should be adjusted to the lowest position. Detergent / Rinse aid • 5 + 25 cm3, in accordance with EN50242-DIN 44990 IEC 436 (international norms) / Rinse aid dosage adjustment: 4. Programme test • Eco 50°C, in accordance with EN 50242 (international norms.). fig.
Programme Listing Programme name and temperature Auto Intensive 60-70O Autonormal 50-60O Autodelicate 30-50O Intensive 60O Express 60O Eco 50O Quick 40O Prewash - Intensive+ 70° (Intensive 60° and prewash function) Level of soil High High Low High Medium Medium Low - High Detergent required A+B A+B A A+B A+B A+B A - A+B Prewash Prewash Prewash Prewash Prewash Prewash The dishwasher is equipped with a sensor that automatically adjusts the washing time, temperature and amou
Care and Maintenance Before beginning any care or maintenance, you should always disconnect the appliance from the electricity supply, and also turn off the water supply. Door seals Wipe the dishwasher door seals regularly with a damp cloth to remove any residues. Filters You should clean the filters at least once a month. 1. Remove the lower basket. 2. Turn the microfilter anticlockwise and then lift it out as in figure 14. 3. Remove the coarse filter from the microfilter (figure 15). 4.
Please note: Never run a programme without the filters in place. Incorrect fitting of the filters may reduce wash performance and potentially damage your appliance. Spray arms You should clean the spray arms at least once a month. 1. Remove the lower basket 2. Pull the lower spray arm upwards to remove it. 3. To remove the upper spray arm, first remove the nut on the upper spray arm by turning it. You should clean and rinse the spray arms thoroughly before replacing them.
Failure Codes and Troubleshooting The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance.
Failure Codes and Troubleshooting Problem Possible cause Check the plug, fuse and circuit breakers of the mains supply. The programme will not start The water tap is turned off. The dishwasher door is not fully closed. The water inlet filter or the machine filters are blocked. Water remains inside the dishwasher at the end of a programme The water drain hose is blocked or kinked. The filters are blocked. Power failure. The dishwasher stops in the middle of a programme Water inlet failure.
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
electric shock. A suitable alternative plug of at least 13 Amp rating to BS 1363 should be used. As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:• The wire which is coloured GREEN and YELLOW must be connected to the terminal which is marked with letter (E) or by the Earth symbol or coloured GREEN and YELLOW.
Installation • D o not install this appliance if it is damaged in any way. Installing a damaged appliance may invalidate the warranty. • The water supply tap should be located in an adjacent cupboard so that it can be accessed after installation. • Ensure the appliance is level by adjusting the feet as necessary. The dishwasher is equipped with an adjustable rear foot that can be raised or lowered by means of an adjustment screw, located in the centre of the kick plate.
The drain hose should be no longer than 4m in length to ensure good performance from the dishwasher. • To prevent siphoning, ensure that the water outlet is not pushed too far into the waste standpipe. The lowest part of the water outlet should be level with the bottom basket of the dishwasher. • When connecting to the sink, ensure that the waste pipe runs higher than the level of the sink bowl to prevent siphoning. • This appliance is cold fill only.
The machine is supplied with a fitting template and these instructions should be followed as normal. Fitting template X Door height Where non-standard integrated appliance doors are supplied, additional fitting instructions are required to ensure compatibility with this product. Y offset Fitting the integrated appliance door fig. 21 However, the fitting template needs to be located lower down the fascia door; this is shown below.
Please contact our Customer Care Department, or for Service on the details below. Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
