WC370 Integrated Intelligent dishwasher Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Important • Read the instructions prior to installation and use of the appliance. • Do not lean or climb on the open dishwasher door to prevent damage. • Close the dishwasher door after use to prevent accidents. • Use only detergents, salt and rinse aid specifically designed for dishwashers. • Do not put solvents in the dishwasher detergent compartment to prevent risk of explosion • Only put dishwasher safe items into the dishwasher. If in doubt, check with the manufacturer of the items.
Control Panel 1 2 3 4 5 6 7 8 Power button (1) • To switch the dishwasher on or off, press the power button (1). When you switch on the dishwasher, the end of programme light will illuminate, and two dashes will appear on the display. Programme display (2) The programme display shows the selected programme and the remaining time to run. If there is a fault on the dishwasher, the fault code will show on the display.
Please note: You should ensure that there are no dishes in the upper basket when running a lower basket halfload programme, and none in the lower basket when running an upper basket half-load programme. If you have selected any extra function (3 in 1, prewash, half-load) for a programme, this function will automatically be selected the next time the dishwasher is used.
Detergent To fill the detergent compartment 1. Push the latch to open the compartment. 2. Add the required amount of detergent. The main detergent compartment “b” (figure 1) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, to be used depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment “a” (figure 1). 3.
Salt To ensure the best efficiency, the dishwasher needs soft water. Hard water means that lime residues remain on the dishes and the interior of the dishwasher, affecting performance. The softener system is designed to remove the ions that make the water hard to provide the best quality wash performance. This is achieved by using dishwasher salt. To add dishwasher salt, follow the steps below: 1. Remove the lower dishwasher basket and then unscrew the salt compartment cap, as shown in figure 2. 2.
Softener Adjustment The efficiency of your dishwasher depends on the softness of the tap water. To ensure best efficiency, the dishwasher is equipped with a system that reduces the hardness in the mains water supply. The efficiency will increase when the system is correctly set. To find out the water hardness level of your water supply you can use the test strip supplied or alternatively contact your local water board.
Rinse Aid To fill the rinse aid compartment 1. Open the rinse aid compartment by turning and removing the cap as shown in figure 5. 2. Fill the rinse aid compartment until the rinse aid indicator goes dark, as shown in figure 6 (where a indicates the compartment is empty, and “b” indicates the compartment is full). 3. Replace the cap, ensuring the markers on the cap line up with the compartment prior to screwing the cap back in place. Rinse Aid Adjustment The level of rinse aid use is preset to 3.
Dishwasher Baskets Top basket height adjustment while it is The upper basket has two different heights available, to allow for larger products in either the upper or lower basket.
Standard Loading and Test Data Capacity • Upper and lower baskets: 12 place settings. • The upper basket should be adjusted to high position. • Cups should be placed on to the dish rack pins. Detergent / Rinse aid • 5 + 25 cm3, in accordance with EN50242-DIN 44990 IEC 436 (international norms) / Rinse aid dosage adjustment: 4. Programme test • Eco 50°C, in accordance with EN 50242 (international norms.).
Programme Listing Programme name and temperature Auto Intensive 60-70O Autonormal 50-60O Autodelicate 30-50O Intensive 60O Express 60O Eco 50O Quick 40O Prewash - Intensive+ 70O Level of soil High High Low High Medium Medium Low - High Detergent required A+B A+B A A+B A+B A+B A - A+B Prewash Prewash Prewash Prewash Prewash Prewash The dishwasher is equipped with a sensor that automatically adjusts the washing time, temperature and amount of water required.
Care and Maintenance Before beginning any care or maintenance, you should always disconnect the appliance from the electricity supply, and also turn off the water supply. Door seals Wipe the dishwasher door seals regularly with a damp cloth to remove any residues. Filters You should clean the filters at least once a month. 1. Remove the lower basket. 2. Turn the microfilter anticlockwise and then lift it out as in figure 9. 3. Remove the coarse filter from the microfilter (figure 10). 4.
Failure Codes and Troubleshooting The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance.
Failure Codes and Troubleshooting Problem Possible cause Check the plug, fuse and circuit breakers of the mains supply. The programme will not start The water tap is turned off. The dishwasher door is not fully closed. The water inlet filter or the machine filters are blocked. Water remains inside the dishwasher at the end of a programme The water drain hose is blocked or kinked. The dishwasher stops in the middle of a programme Water inlet failure. The filters are blocked. Power failure.
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
Installation • o not install this appliance if it is damaged in any way. Installing D a damaged appliance may invalidate the warranty. • he water supply tap should be located in an adjacent cupboard T so that it can be accessed after installation. • nsure the appliance is level by adjusting the feet as necessary. E The dishwasher is equipped with an adjustable rear foot that can be raised or lowered by means of an adjustment screw, located in the centre of the kick plate.
Fitting the integrated appliance door Y offset Where non-standard integrated appliance doors are supplied, additional fitting instructions are required to ensure compatibility with this product. Fitting template However, the fitting template needs to be located lower down the fascia door; this is shown below. The amount of offset, Y, depends on the height of the fascia door and can be calculated as X = 723mm.
Notes 19
Please contact our Customer Care Department, or for Service on the details below. Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
