WC370 Integrated Dishwasher Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
rtant Important The CDA be Group cannot be responsible injuries losses caused incorrect of usethis or installation of this Group Ltd cannot heldLtd responsible forheld injuries or lossesforcaused byor incorrect use or by installation Please note CDA reserve the right to invalidate thewith guarantee supplied with thisincorrect product following incorrect Please noteproduct. that CDA reserve thethat right to invalidate the guarantee supplied this product following installation or misuse of the appliance.
• The plastic housing on the water inlet pipe contains an electrically operated valve. The wires that connect to this valve are inside the inlet hose. Do not cut through the inlet hose, and do not put the plastic housing in water. • Children could get locked inside the appliance. Therefore when disposing of an old appliance, cut off the plug and set aside, and damage the door lock so that the door can no longer be closed.
Control Panel 1 2 3 4 5 6 7 8 Power button (1) • To switch the dishwasher on or off, press the power button (1). When you switch on the dishwasher, the end of programme light will illuminate, and two dashes will appear on the display. Programme display (2) The programme display shows the selected programme and the remaining time to run. If there is a fault on the dishwasher, the fault code will show on the display.
Please note: You should ensure that there are no dishes in the upper basket when running a lower basket half-load programme, and none in the lower basket when running an upper basket half-load programme. If you have selected any extra function (3 in 1, prewash, half-load) for a programme, this function will automatically be selected the next time the dishwasher is used.
1. Push the latch as shown in figure 1. 2. Add the required amount of detergent. The main detergent compartment “b” (figure 2) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, to be used depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment “a” (figure 2). 3. Then close the detergent compartment lid until the latch locks.
compartment “b” (figure 2) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, to be used depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment “a” (figure 2). 3. Then close the detergent compartment lid until the latch locks. fig 1 Please note: You should only use detergents designed specifically for Detergent use in dishwashers.
ENGLISH Testing strip The washing effectiveness of your machine depends on the softness of the tap water. For this reason, your machine is equipped with a system that reduces the hardness in mains water supply. The washing effectiveness will increase when the system is correctly set. To find out the water hardness level of water in your area, contact your local water board or determine water hardness level by using the test strip(if available).
nse Aid RinseRinse Aid Aid fill the rinse aid compartment Rinse Aid To fill theTorinse aid rinse compartment fill the compartment To fill the rinse aidaid compartment Open the rinse aid compartment by turning and removing the cap as 1. Open the rinse aid compartment by turning andand removing thethe capcap as as 1. Open the rinse aid compartment by turning removing shown in figure 4. 1. Open the rinse aid compartment by turning and removing the cap as shown in figure shown in figure 4. 5. in figure 4.
Top basket height adjustment while i Dishwasher Baskets The upperthe basket hasoftwo heights available, to allow for larger Baske To adjust height thedifferent upper basket: your m products in either the upper or lower basket. To raise or lower the upper Top basket height adjustment while it is full Top basket height adjustment while it is full 1.
Standard loading Loadingand andTest TestData Data Capacity • Upper and lower baskets: 12 place settings. • The upper basket should be adjusted to high position. • Cups should be placed on to the dish rack pins. Detergent / Rinse aid 3, in • 5 + 25 cm cm3, in accordance accordance with with EN50242-DIN EN50242-DIN 44990 44990 IEC IEC 436 436 (international norms) / Rinse aid dosage adjustment: 4.
Programme Listing Programme name and temperature Auto Intensive 60-70O Autonormal 50-60O Autodelicate 30-50O Intensive 60O Express 60O Economy 50O Quick 40O Prewash - Intensive+ 70O Level of soil High High Low High Medium Medium Low - High Detergent required A+B A+B A A+B A+B A+B A - A+B Prewash Prewash Prewash Prewash Prewash Prewash The dishwasher is equipped with a sensor that automatically adjusts the washing time, temperature and amount of water required.
Unplug your machine ime maythat accumulate intemperature, the machine's section.InIncase case such gramme runs at high andwashing start the machine. ofof insufficiency, useand turn off its ta Do not use hard materials when cleani ation; ecial cleansing material available in the market. (Cleansing material produced special to and a dampened cloth. chines bycompartment detergent producers.) etergent without loading any dishes into the machine, select a me that runs at high temperature, and start the machine.
Failure Codes and Troubleshooting The programme indicators also serve as a diagnostic display to help in the event of a problem with the appliance. Error Code Error description F1 Alarm is active against water overflow. Advice Turn off the dishwasher and disconnect the water supply. Contact CDA service. Drain hose is blocked. F2 The waste water in the machine can not be discharged. The filters of your machine might be blocked. Restart the dishwasher and cancel the programme.
Failure Codes and Troubleshooting Problem Possible cause Check the plug, fuse and circuit breakers of the mains supply. The programme will not start The water tap is turned off. The dishwasher door is not fully closed. The water inlet filter or the machine filters are blocked. Water remains inside the dishwasher at the end of a programme The water drain hose is blocked or kinked. The filters are blocked. Power failure. The dishwasher stops in the middle of a programme Water inlet failure.
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
Installation • not install install this thisappliance applianceififititisisdamaged damagedininany anyway. way.Installing Installinga a • Do Do not damaged appliance may invalidate the warranty. damaged appliance may invalidate the warranty. • The water supply tap should be located in an adjacent cupboard so that it • The water supplyafter tap should be located in an adjacent cupboard so that it can be accessed installation. can be accessed afterisinstallation.
Fitting the integrated appliance door Where non-standard integrated appliance doors are supplied, additional fitting instructions are required to ensure compatibility with this product. The machine is supplied with a fitting template and these instructions should be followed as normal. However, the fitting template needs to be located lower down the fascia door; this is shown below. The amount of offset, Y, depends on the height of the fascia door and can be calculated as X = 723mm.
Notes 18
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
