WC140 Integrated Dishwasher Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
rtant Important The CDA be Group cannot be responsible injuries losses caused incorrect of usethis or installation of this Group Ltd cannot heldLtd responsible forheld injuries or lossesforcaused byor incorrect use or by installation Please note CDA reserve the right to invalidate thewith guarantee supplied with thisincorrect product following incorrect Please noteproduct. that CDA reserve thethat right to invalidate the guarantee supplied this product following installation or misuse of the appliance.
Recommendations Recomendations toto loading thethe dishw• • To reduce energy and and water waterconsumption, consumption,remove removeallalldirt dirtresidues residuesfrom fromthe thedishes dishesprior prior loading dishwasher. when loaded. • Only run the the dishwasher dishwasheronly when fullyfully loaded. • • Place Place hollow hollow items items (bowls, (bowls,glasses glassesand andpans) pans)face facedown downininthe thebasket. basket.
Starting a programme • Press the Power button. • Press the Programme Selection button until the required programme light is illuminated. • If required, press the Delay Timer button. • Once the power is switched on, the end of Programme Indicator light will switch on. • Once a programme is selected, the end of Programme Indicator light will switch off, and the Programme Indicator light will switch on. • When you close the dishwasher door the programme will start automatically.
1. Push the latch as shown in figure 1. 2. Add the required amount of detergent. The main detergent compartment “b” (figure 2) has lines to allow for specific amounts of detergent. These are marked at either 15 cm3 or 25 cm3, to be used depending on how dirty the dishes are. If your dishes are in need of an intensive wash, then add 5 cm3 of detergent into the prewash section of the compartment “a” (figure 2). 3. Then close the detergent compartment lid until the latch locks.
Testing strip The washing effectiveness of your machine depends on the softness of the tap water. For this reason, your machine is equipped with a system that reduces the hardness in mains water supply. The washing effectiveness will increase when the system is correctly set. To find out the water hardness level of water in your area, contact your local water board or determine water hardness level by using the test strip(if available).
nse Aid RinseRinse Aid Aid fill the rinse aid compartment Rinse Aid To fill theTorinse aidrinse compartment fill the aidcompartment compartment To fill the rinse aid Open the rinse aid compartment by turning and removing the cap as 1. Open the rinse aid compartment by turning and removing the cap 1. Open the rinse aid compartment by turning and removing the as cap as shown in figure 4. 1. Open the rinse aid compartment by turning and removing the cap as shown inshown figurein4.figure 4. in figure 4.
Dishwasher Baskets To adjust the height of the upper basket: 1. Open the basket retaining clips, as shown in figure 7, but turning them to the side. 2. Remove the upper basket, and relocate the alternate set of wheels on the runner, as shown in figure 8, pushing the basket back into place. 3. Close the basket retaining clips. fig 7 The images below are designed as guidance as to best practice for loading the dishwasher.
Standard loading and Test Data Capacity • Upper and lower baskets: 12 place settings. • The upper basket should be adjusted to high position. • Cups should be placed on to the dish rack pins. Detergent / Rinse aid • 5 + 25 cm3, in accordance with EN50242-DIN 44990 IEC 436 (international norms) / Rinse aid dosage adjustment: 4. Programme test • Economic 50°C, in accordance with EN 50242 (international norms.).
Programme Listing Programme names and temperatures Intensive 65°C (P1) Normal 55°C (P2) Economic 50°C (P3) Quick 40°c (P4) Prewash No Heat (P5) Type of food waste soups, sauces, pasta, eggs, pilaf, potato and oven dishes, fried foods soups, sauces, pasta, eggs, pilaf, potato and oven dishes, fried foods coffee, milk, tea, cold meats, vegetables, not kept for long coffee, milk, tea, cold meats, vegetables, not kept for long Pre-wash to rinse and loosen residue-awaiting full load-then select a prog
Unplug your machine ime maythat accumulate intemperature, the machine's section.InIncase case such gramme runs at high andwashing start the machine. ofof insufficiency, useand turn off its ta Do not use hard materials when cleani ation; ecial cleansing material available in the market. (Cleansing material produced special to and a dampened cloth. chines bycompartment detergent producers.) etergent without loading any dishes into the machine, select a me that runs at high temperature, and start the machine.
Failure Codes and Troubleshooting Your dishwasher control panel is equipped with a diagnostic display to help in the event of a problem with the appliance.
Failure Code and Troubleshooting Problem The programme will not start Water remains inside the dishwasher at the end of the programme Possible cause Check the plug, fuse and circuit breakers of the mains supply The water tap is turned off The dishwasher door is not fully closed The water inlet filter or the machine filters are blocked The water drain hose is blocked or kinked.
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
Installation • Do not install this appliance if it is damaged in any way. Installing a damaged appliance may invalidate the warranty. • The water supply tap should be located in an adjacent cupboard so that it can be accessed after installation. • Ensure the appliance is level by adjusting the feet as necessary. • Only use the water inlet supplied with the appliance. • If the water pressure is above 10 bar, a pressure relief valve should be used.
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
CDA Dishwasher – Oversized Fascia Door Mounting Information Scope of Document: Where non-standard integrated appliance doors are supplied, additional fitting instructions are required to ensure compatibility with this product. Instructions: The machine is supplied with a fitting template and these instructions should be followed as normal.
