sk450 Single Ecoclean Oven Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important This appliance must only be used for the purpose for which it is intended, i.e. domestic cooking, defrosting and reheating foods. Any other use could be dangerous and may lead to premature failure of the appliance. The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
CE Declarations of Conformity: This oven has been designed, constructed and marketed in compliance with safety requirements of EEC Directive 2006/95/EEC (Low voltage) and requirements of EMC Directive 2004/108/EEC. This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (LVD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109.
Important • Read the user instructions carefully before using the oven for the first time. • Follow the instructions for first use of the oven. • Clean the oven regularly. • Remove spills as soon as they occur. • Always use oven gloves when removing shelves and trays from the ovens. • Do not allow children near the oven when in use. • Do not allow fat or oils to build up on the oven shelves, grill pan or oven base. • Do not place any cooking utensils or plates directly on the oven base.
Using the Touch Controls The touch controls should be used with the flat of your finger, rather than the fingertip. fig.
The Control Panel A B C D J K E F G L M fig.
N: O: P: Q: R: S: T: U: V: W: X: Y: Z: N O U V P W Q X R S Y Z T Fan oven + lower heat Defrost Auto recipe Confirm Scroll downward / Reduce power Scroll upward / Increase power Digital display Timer function Timer - cooking time Timer - end time Minute minder Decrease settings Increase settings 7
Before First Use When the oven is connected to the electrical supply for the first time, the display will ask you to select your language: Use the buttons to select the language you want, use the “ok” button to confirm your choice. The oven will remember your language preference, even after future power outages. After setting the language, the oven will go into “demonstration” mode (it will also go into this mode after any power failure).
General Settings & Use Clock To set the clock, touch the “Timer function” key for at least 3 seconds, the clock will show “00:00” with the separator dots flashing. Use the “+” and “-” keys to set the correct time: Five seconds after selecting the time the dots will stop flashing and the time will be set. Key lock This appliance is equipped with a key lock to prevent accidental use. For safety reasons the “On/Off” key will work to switch the appliance off when the key lock is set.
To turn the oven on Touch the “On/Off” key briefly, it gives one short beep followed immediately by a long one, the word ”ON” appears on the display for approximately one minute. To turn the oven off Touch the “On/Off” key briefly, it gives one long beep, the word ”OFF” appears briefly on the display. While the word “ON” is showing on the display, any of the cooking functions can be selected by touching one of the function keys.
Warming oven First touch the “On/Off” key (as p10), then touch the “Warming oven” key. The warming oven programme allows you to prove dough and bake blind, using just heat from below. The cooking temperature defaults to 50°C and can be set between 50-250 (MAX) °C in 5˚C increments. The temperature can be changed at any time by touching the keys. During heating the “°C” symbol flashes and the display shows the actual temperature in the oven.
Fanned grill First touch the “On/Off” key (as p10), then touch the “Fanned grill” key. The fanned grill programme uses the grill element for grilling and the fan to help circulate heat around the food. This is ideal for cooking on several shelves. The cooking temperature defaults to 165°C and can be set between 50-250 (MAX) °C in 5˚C increments. The temperature can be changed at any time by touching the keys. During heating the “°C” symbol flashes and the display shows the actual temperature in the oven.
The temperature can be changed at any time by touching the keys. During heating the “°C” symbol flashes and the display shows the actual temperature in the oven. Fan oven + lower heat First touch the “On/Off” key (as p10), then touch the “Fan oven + lower heat” key. The fan oven + lower heat programme uses the fan element to enhance the heat from the bottom element to create an ideal environment for cooking pizzas.
Use of the Food Probe The food probe is a thermometer which, when inserted into your food in the oven, makes it possible to check its internal temperature and use it to establish when it is cooked through. Using the food probe 1. The probe must be plugged into the oven before the oven is switched on. 2. Locate the food probe socket, situated in the top front corner of the oven cavity, protected by a metal cover. 3. Lift the metal cover. 4. Push the plug in as far as it will go.
If at any time you want to change either the probe set temperature or the oven setting temperature, touch the “ok” key to toggle the display between the setting temperatures. Then use the keys to adjust the setting. Note: When using the food probe the preset temperatures for all programmes are changed. The cooking temperature with probe defaults to 165°C and can be set between 120-250°C. Note: The defrosting programme is deactivated when the probe is plugged in.
preheat” key again, the oven beeps twice and the “Rapid preheat” key returns to white lighting to show this is deactivated. Oven clean This function cleans the oven’s catalytic side and rear panels by running a maximum temperature cycle. The “Oven clean” function can only be used when no cooking function has been selected. First touch the “On/Off” key (as p10), then touch the “Oven clean” key for five seconds. The oven light is switched on and can be switched off and on again at any time.
select the option required then confirm by touching the “ok” key for each selections. At the end of the process the oven displays the set cooking time; this may be adjusted up or dow using the “+” and “-” keys, then the “ok” to to start the programme running. confirm. Press the “Start” key For some programmes the oven determines that a period of preheating is required.
Timer and Minute Minder Programming the oven This is only applicable to these functions:Fan oven Fan oven + grill Fan grill Grill Any timer functions required should be set after the relevant cooking programme has been set, and before the “start” key is touched. Timer - Cooking time Touch the “Timer function” key once so the “Cooking time” key lights up.
Programming delayed cooking This is achieved by programming an end time (when you want the food ready) and also programming a cooking time (as the recipe). Minute minder The minute minder is a timer that is independent of the function of the oven; it times and sounds a beep but does not affect any oven functions. This is useful for timing actions that are unrelated to this appliance, for example timing eggs on the hob.
Care and Maintenance IMPORTANT: Always disconnect the appliance from the power supply before undertaking any cleaning or maintenance. You should always allow the oven to cool fully after use before undertaking any cleaning or maintenance. Changing the oven lamp • Remove all shelves and the grill pan from the oven. • Gently unclip the side rack from its lower locating stud and unhook its top to remove it. Note: No tools are required and the stud should not be removed.
cause premature failure. Always use a clean cloth or gloves. • Reattach the glass cover, pressing it firmly into position. • Hook the catalytic panel back into position. • Replace the side rack by locating the two hooks at the top and clipping it back into position on its lower fixing stud. • Replace the oven shelves and grill pan as necessary. Please note: Bulb replacement is not covered by your guarantee.
Cleaning You should only use non-abrasive cleaners. Any abrasive cleaners (including Cif) will scratch the surface and could erase the control panel markings. You should not use cleaning products with a chlorine or acidic base. Any spillages should be cleaned off immediately, especially any alkaline or acidic substances (lemon juice, vinegar etc.) Stainless steel Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth.
Catalytic liners The catalytic oven liners must only be cleaned with fresh water. For stubborn stains, boil a cup of water in the oven for 2 to 3 minutes. Steam will soften the marks prior to cleaning. Grill When used regularly, the grill element does not need cleaning as the intense heat will burn off any splashes. The interior ceiling may need regular cleaning, which should be done with warm water, detergent and a sponge.
Installation The appliance can be installed under a worktop or in a wall unit (open or closed) with the appropriate dimensions for recessed installation. Centre the oven in the unit so as to ensure a minimum distance of 10mm between the appliance and the surrounding unit. The material of the unit supporting the appliance must be heat resistant (or covered with a heat resistant material). For greater stability, attach the oven to the unit with two screws through the holes provided on the side panels.
540 560 595 594 50 510 594 597 535 21 Fig. 6 540 560 595 594 50 510 594 597 535 21 Fig.
Mains Electricity Connection Warning! This appliance must be earthed Fig. 8 We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations. This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13A plug or 13A supply. This appliance is intended to be connected to fixed wiring by a double pole switch, having a contact separation of at least 3mm in all poles.
This appliance is supplied with a 3 core mains cable; the wires are in accordance with the following code: Green and Yellow = Earth Blue = Neutral Brown = Live Please note: • The mains cable must only be replaced by a qualified electrician or service engineer and must be of equivalent or better rating (i.e. 1.5mm2, HO5V2V2-F). • The current rating of the fuse or circuit breaker protecting this appliance should be marked on the socket outlet (16A).
Please contact our Customer Care Department for Service on the details below. Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
