he6050ss electric hob Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : customer.care@cda.eu W : www.cda.
Contents: 3 5 6 8 9 11 12 14 2 Important Important Notes Using Your Hob Efficient Use Of Your Hob Care And Maintenance Fitting The Hob How To Install The Hob Mains Electricity Connection
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance or use in a commercial environment.
CE Declarations of Conformity: This appliance has been manufactured to the strictest standards and complies with all applicable legislation, including Electrical safety (LVD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
Important Notes • P lease note: • Electric hobs become hot and remain hot during and immediately after use. Do not touch the hob until it has been allowed to cool. • Keep children away from the appliance when in use. • Never use the hob top for storage. • Pan handles should never stand out beyond the edge of the worktop. This will ensure children cannot reach them. • Do not switch on the hotplates without cookware in place. • Do not lean over the hob when it is in use.
Using Your Hob 2 3 5 6 8 1 7 4 9 Fig.1 Electric hotplates: 1. 180mm (FL) 1.5kW 2. 145mm (BL) 1.0kW 3. 180mm (BR) 2.0kW Rapid 4. 145mm (FR) 1.5kW Rapid Control panel: 5. (BR) 180mm Rapid hotplate control 6. (BL) 145mm hotplate control 7. (FL) 180mm hotplate control 8. (FR) 145mm Rapid hotplate control 9. Hob in use indicator light HOTPLATE SWITCHES: The power of each hotplate can be varied using the control knob to select the required heat.
The ‘OFF’ position is indicated by the symbol ‘O’. The indicator will light when the hotplate is in use. When you have finished cooking, check to ensure that the hotplates are off and the indicator is not lit. Before using your hob for the first time, switch the hotplates on for a FEW SECONDS to burn off any grease left over from the manufacturing process.
Efficient Use Of Your Hob The hob is equipped with hotplates of different sizes, designed to accommodate most shapes and sizes of pan. For best results, only use pans with flat bottoms and choose an appropriate hotplate depending on the size of the pan. The most efficient use of the hob is shown below, where the pan and hotplate are correctly chosen. Use pan lids where possible to minimize the energy usage of your appliance. Turn off each hotplate a few minutes before the end of cooking time.
Care and Maintenance The hob has a stainless steel surface, you should use a non-abrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and washing up liquid and drying to a shine with a clean cloth. Over time with use, the stainless steel surface may discolour; this is normal and does not constitute a fault with this appliance.
IF YOUR HOB IS NOT WORKING: 1. Check that the mains supply has not been switched off. 2. Check that the fuse or circuit breaker has not blown/tripped.
Fitting The Hob Unpacking the hob: • Take care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 150mm away from any adjacent vertical surfaces, e.g. a tall cupboard end panel. This may be reduced to 125mm if the adjacent surface is resistant to fire (tiles or steel, for example). These dimensions are shown in Fig 3.
Notes: • Do not position this appliance above a refrigeration unit. The heat generated may cause the unit to fail. • This appliance is designed to be installed into cabinet units capable of withstanding temperatures of 65°C above ambient or greater (typically 80-90°C). • If the hob is to be installed above a working drawer, then a partition should be fitted to protect the contents and user from the heat generated during use. This should be fitted 100mm below the hob.
>61.5mm 477mm >600mm 560cm 557mm 185mm >165mm 185mm >165mm Fig.3 Fig.4 3cm Fig.5 4cm Fig.
Mains Electricity Connection Warning! this appliance must be earthed We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.T. and local regulations. This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13A plug or 13A supply. This appliance is intended to be connected to fixed wiring by a double pole switch, having a contact separation of at least 3mm in all poles.
• W hen installing this product we recommend you seek the help of another individual. TECHNICAL DATA: The table opposite shows the rated output of each hotplate: Mains electrical voltage: 230 - 240Vac, 50Hz Total rated electrical input: 6.0kW Hotplate Size Nominal Rating (kW) 180mm 1.5 145mm 1.0 180mm Rapid 2.0 145mm Rapid 1.
Please contact our Customer Care Department for Service on the details below Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
