FWV460 Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance. Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel.
Icemaker Display Control Panel Water Nozzle Ice Drawer Drip Tray Icemaker control panel ON 1 OFF 2 3 4 5 1. On button 2. Off button 3. Water glass button – this button dispenses a small amount of water. 4. Water jug button – this button dispenses a large amount of water. 5. Manual water button – this button dispenses water as long as the button is pressed. 6. Maintenance button – this button allows the icemaker to automatically empty the pipes.
The Icemaker Before first use: 1. Pull the machine out of its housing by lifting the handle of the machine and pulling it towards you. 2. Fill the water tank (even if the appliance is to be plumbed in to the mains water supply). 3. Turn on the machine at the switch on the left side of the machine. 4. Push the machine back into the housing. 5. Switch on the machine by pressing the ON button. 6 The machine is now ready for use and the display shows ICE ON WATER READY.
The Icemaker To make ice The icemaker will make ice automatically once it is switched on and will continue to make ice until the ice compartment is full. Whenever ice is removed, the icemaker will make more ice until the compartment is full again. To dispense water The amount of water dispensed from the water nozzle is controlled by three different buttons. Button 3 – water glass Button 4 – water jug Button 5 – manual setting – this button dispenses water as long as the button is pressed.
Care and maintenance Always disconnect the appliance from the power before any cleaning or maintenance. As the icemaker has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Stainless steel can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. Proprietary stainless steel cleaners are available.
Troubleshooting Problem Solution: WATER MISSING shows in the display The water tank is empty and needs to be refilled ICE FAULT WATER READY shows in the display at first switch on Turn the icemaker off with button 2 and the main switch on the side, before switching it on again. The icemaker emits a continuous beep UV Sterilizer needs replacing - contact CDA Customer Care IMPORTANT: Do not operate with a damaged cord, plug, after the appliance malfunctions or has been damaged in any way.
Installation min. 200cm2 IMPORTANT: THIS APPLIANCE SHOULD BE FITTED BY SUITABLY QUALIFIED PERSON. 600 450 min 560 1. Slide the base unit into the housing ensuring the dimensions are correct as per figure 1. 2. Fix the base unit in place by attaching the 10 screws in to the holes as shown in figure 2 and figure 3. If the sides of the base are not flush with the sides of the housing, then use the shims provided. 3. Push the runners fully closed on the base unit. 4.
Installation Please note: Due to the weight of this appliance, the furniture unit must be secured to the wall prior to installation. You must ensure that all water connections are sound and check there are no leaks before completing installation. For best performance, the mains water pressure must be between 0.1 - 3 bar. fig. 4 Do not use outdoors. Do not install near a hob or oven. To reduce the risk of electric shock, do not mount over a sink. Flow restrictor fig.
Electrical information Warning! This appliance must be earthed. The mains lead of this appliance has been fitted with a BS 1363A 13 amp fused plug. To change a fuse in this type of plug, follow the steps below: 1. Remove the fuse cover and fuse. 2. Fit replacement 13A fuse, ASTA approved to BS 1362 type, into the fuse cover. 3. Replace fuse cover. Important: Do not use the appliance without the fuse cover in position.
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
