DC740 Built-Under Double Oven DC940 Built-In Double Oven Manual for Installation, Use and Maintenance Passionate about style 1 Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
Important This appliance must only be used for the purpose for which it is intended, i.e. domestic cooking. Any other use could be dangerous and may lead to premature failure of the appliance. The CDA Group Ltd cannot be held responsible for injuries or losses caused by incorrect use or installation of this product. Please note that CDA reserve the right to invalidate the guarantee supplied with this product following incorrect installation or misuse of the appliance.
Important • Read the user instructions carefully before using the oven for the first time. • Follow the instructions for first use of the oven. • Clean the oven regularly. • Steam cleaners must not be used when cleaning this appliance. • Remove spills as soon as they occur. • Always use oven gloves when removing shelves and trays from the ovens. • Do not allow children near the oven when in use. • Do not allow fat or oils to build up on the oven shelves, grill pan or oven base.
Oven controls and use Cooking function knob To set the function, turn the cooking function knob for the required oven clockwise to the required function. Each of the oven functions uses different elements within the oven to offer you the best choice of cooking every time. These are explained below: Conventional oven This function uses the top and bottom heating elements only with a temperature between 50ºC and 250ºC..
Programming the oven Please note: • The semi-automatic and automatic cooking programmes will only work with the main oven. • The alert beep will cut off after two minutes if it is not switched off manually. 1 3 2 4 Setting the clock The clock is preset to 12:00, and will revert to this after a power failure. or . When the When the current time indicator is flashing, touch correct time is shown on the display, the clock will set after approximately five seconds’ delay.
Programming the oven Semi-automatic cooking The main oven can be set to switch off automatically at a preset time up to a maximum of 10 hours. To set a semi-automatic cooking programme: • Select the oven function and temperature (the oven will switch on) until the cooking time indicator flashes. • Touch or to select the required duration for the semi-automatic cooking programme. When the correct duration • Then touch shows on the display, wait for approximately five seconds.
Care and Maintenance IMPORTANT Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. The oven exterior As the oven has a stainless steel or enamel surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings.
Changing the Oven Lamp Before any maintenance is started involving electrical parts, the appliance must be disconnected from the power supply. If the oven has been in use, let the oven cavity and the heating elements cool down before attempting any maintenance. Changing the bulb (fig. 2) Unscrew the protective cover. We recommend that you wash and dry the glass cover at this point.
Cleaning and Maintenance Removing the Oven Door The oven doors can easily be removed as follows: • Open the door to the full extent (fig. 3.1). • Open the lever A completely on the left and right hinges (fig. 3.2). • Hold the door as shown in fig. 3. • Gently close the door (fig. 3.3) until left and right hinge levers A are hooked to part B of the door (fig. 3.2). • Withdraw the hinge hooks from their location following arrow C (fig. 3.4). • Rest the door on a soft surface. fig.
Mains Electricity Connection Warning! This appliance must be earthed To connect this appliance to a UK standard mains supply, connect the bridging links between 1-2-3 for the live feed and 4-5 for the neutral feed We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13A plug or 13A supply.
Installation Important Failure to allow adequate ventilation to the appliance may result in overheating or damage to adjacent units and could invalidate the warranty. The diagram below shows the minimum required. o This appliance is type X installation. The walls of the kitchen units must be able to withstand temperatures of 75 C above ambient o o (typically this is between 90 C and 100 C).
To contact our Customer Care Department, or for Service, please contact us on the details below. Passionate about style 12 Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.
