PISLG - inglese REV.06 INSTRUCTION FOR INSTALLATION AND USE HOBS SELECT SERIES built in flush WOLO SERIES STARK SERIES F.lli BARAZZA s.r.l. 31025 Sarano di Santa Lucia di Piave (TV) Via Risorgimento, 14 – Tel +39 0438 62888 Fax +39 0438 64901 www.barazzasrl.it E-mail: info@barazzasrl.
DEAR CUSTOMER F.lli Barazza S.r.l. in present in the household appliances market for over 40 years. Now it would thank you to have bought its appliance and it want to assure you the quality of this product. The use of this appliance is not so difficult, but we would invite you, before starting use it, to read careful the instructions below. FOREWORD - This booklet accompanies the appliance and contains all the information you need to use and take care of it.
INSTRUCTION FOR THE USER Important: The appliance must be installed, regulated, connected to the gas network and electric mains, as well as adapted to the type of gas it will be fed with by qualified personnel, according to the norms in force and following the instructions in the second part of the instruction booklet. Metal utensils should not be left on top of cooker as they are prone to heat up and cause burns.
- How to use the burners Next to each knob there is a symbol that shows which burner it refers to. Each gas burner knob has the following symbols: Stop Maximum setting Minimum setting The burner should be turned on before putting the pan on the rung. To turn a burner on, press the knob right down turning it counter-clockwise to the maximum position and then press the electric ignition button. Let go of the knob after 5 seconds.
- Choosing the burners. For a better use of the burners you should use pans with diameters that match the size of the burners so as to have maximum efficiency using as little gas as possible. It is also essential when you are cooking to centre the pans on the burners and to use their lids. Burner Ø Pan in cm.
INSTRUCTIONS FOR THE INSTALLER Installation must be performed by a qualified installer and conform to local codes, and carried out with extreme care. Prior to installation, ensure that the local distribution conditions (nature of gas and gas pressure) and the adjustments of the appliance are compatible. The gas adjustment conditions for this appliance are stated on the data plate located on the back of the appliance (see fig. 2) F.
- Connecting gas - Ensure that it has been adjusted to local fuel types. If it has not been adjusted, follow adjustment instructions as set out in ‘Adjustments for alternative gas types’. If it is to be fuelled by liquid gas, only a certified and approved pressure regulator is to be used. Connect the appliance to gas cylinder or other gas supply in accordance with local codes and regulations.
TECHNICAL FEATURES Dimensions: FITTED HOBS width depth SELECT size 30 module size 60 module size 70 module size 90 module size 100 module size 120 module size Corner module cm. 30 cm. 58.5 cm. 70 cm. 86 cm. 100 cm. 116 cm. 83 cm. 50 cm. 50 cm. 50 cm. 50 cm. 45 cm. 35 cm. 83 WOLO size 60 module cm. 58.5 cm. 51 STARK size 70 module cm. 71.5 cm. 51 Electrical components: Electronic ignition V.A. 0,6 Isolation category I Supply voltage 230V 50 Hz N.B.
MAINTAINANCE AND CLEANING - Cleaning the hob Before you start cleaning the hob wait until the rungs, burners and hotplates are cold and then, for greater safety, turn the power off via the main switch. Wash the enamelled, painted or chromium parts with warm water and soap or a mild, non-corrosive liquid detergent, avoiding all abrasive substances. Do not leave acid or alkaline substances (lemon juice, vinegar, etc.) on for any length of time as they can ruin the surface.
- Repairs on electrical parts Before calling the Technical Assistance Service check that: - The plug has not come out of the socket. The main switch in the home is on. If necessary, have the appliance serviced by qualified personnel. Remove the plug from socket before disassembling any part. - Replacement of feed cable The feed cable must be in HO5 RR-F, with a cross sectional area of 3x1 mm².
a) Changing the nozzles Remove the rungs, burners and flame dividers. Using the spanner provided with the appliance, remove the nozzles – Fig. 6 and replace them with those enclosed, strictly observing the marking and the following table. NOZZLE HOLDER INTERCHANGEABLE NOZZLE Fig. 6 If the appliance has to be adjusted to suit a different gas source, the installer has to fix the new labels over the old ones. Two labels are found in the guarantee and in the back of appliance.
b) Regulating the minimum To adjust the hob burner minimum, light the burners and turn them down to minimum (serigraphed small flame). Take the knob off (it simply pulls off) and insert the screwdriver (provided with the appliance) in the screw in the knob holder pin (Fig.7): turn this screw to the right to make the flame smaller or to the left to make it bigger until you reach the minimum wanted.
- Lubricating the cocks periodically This must be done by qualified personnel whom you must contact also if the appliance is malfunctioning. It is however advisable each time work is done on the cocks, to change the cocks and gasket. - Knobs - The gas hob burner knobs are ONLY TO BE REMOVED for servicing (regulating the minimum flame) and NOT for cleaning. They are to be replaced in the correct order and in their original position. Any changes will result in the appliance malfunctioning.
ATTENTION This appliances can be installed and used only on permanently ventilated premises in accordance with the standards. - Installation premises To ensure the gas-run appliance works properly the room in which it is installed must have enough air for the combustion gas, in compliance with the current standards. Vents with a minimum section of at least 100 cm², must be made so they cannot be obstructed either from indoors or outdoors and located close to the floor Fig.
HEIGHT = 56 cm DISTANCE FROM THE SIDE = RIF.A DISTANCE FROM THE BACK = RIF.B Fig. 9 RIF.A RIF.
FITTING A HOB INTO A MODULAR UNIT The hobs can be mounted on all units in wood, laminated plastic, metal and granite provided they are heat resistant (120°C). The appliances are classified type y, therefore, if there is a side wall it can be higher than the hob. Fitted hobs are class 3; 100 min These appliances can also be fitted on top of an oven. If the hob is fitted on top of an oven a separating panel must be used, putting it on top of the oven, at a distance from the undercounter of at least 100 mm.
SIZES OF THE FITTED AND SUPPORTED HOBS AND HOUSING HOLES Measurements in mm.
Select 120 module – built in 27 Select 100 module – built in 11 18 35 0 3 45 45 0 0 98 43 0 3 30 Select 90 corner module – built in 0 83 45 10 50 0 20 60 5 5 48 60 3 00 10 0 33 0 81 0 21 40 11
Select 70 module – flush Select 90 module – flush R 0 55 674 0 0 83 50 0 R 26.5 4 50 80 3 R 26.5 0 68 03 7 0 84 63 8 4 50 80 3 Lowering belt h=1.7 mm Lowering belt h=1.7 mm Select 100 module – flush Select 120 module – flush 00 10 R 0 85 97 0 18 60 11 20 11 35 0 R 26.5 4 45 30 3 25 98 46.5 45 0 25 28.5 R 25 46.5 86 18 0 70 50 0 25 28.5 R R 26.5 0 03 10 33 0 35 3 40 1 1 163 1 Lowering belt h=1.7 mm Lowering belt h=1.
Wolo 60 module – built in 0 8 5 71 51 0 48 0 43 41 51 5 11 58 Stark 70 module – built in 56 48 0 0 0 68 ASSEMBLY DIAGRAM FOR FITTED HOBS The hobs are provided with brackets so they can be fixed on any type of top, as per the following diagram: Silicone Silicone Piano Silicone Top Hob Piano Hob 10 10 1,7 30 / 40 1,5 30 / 40 3 Top Staffa Staffa Bracket Bracket Vite Vite Screw Screw Fig.
ATTENTION This appliance has to be disposed off in accordance with local rules and regulations regarding.
