User’s Manual for Smart Constant Speed Dome Camera Please read the manual carefully before installing and using the unit.
Table of Contents PART I: INTRODUCTION.......................................................................................................................................2 1-1 INSTRUCTIONS:........................................................................... 2 1-2 CHARACTERISTICS ..................................................................... 2 1-3 MAIN TECHNICAL DATA ............................................................. 3 PART II: INSTALLATION PROCEDURES..............................
Part I: Introduction 1-1 Instructions: We greatly appreciate your choosing our product! The product is under one year warranty, including free maintenance or spare parts replacement. Do not dismantle and repair the unit without the company’s authorization. Damage or breakdown arising from the following circumstances is No free maintenance: 1. dismantling and repairing of the unit without the company’s authorization; 2.
anti-interruption ability 11. If the power is off when the unit is scanning or cruising, it will automatically resume scanning or cruising once power supply is on. 12. Support 16 preset positions, 1 tour, left & right scan, 360° scan. 13. The unit has one guard position; the user can preset it for a key monitor area according to the actual conditions. If not operated after 5 minutes, it will automatically monitor the preset position. DC14V---15V Dome motor DC14V---15V/0.
Part II: Installation Procedures 2-1 Outer shape and installation size 1, JE900BN 2, JE900BNC 2-2 Installation of Dome Cover 1, JE900BN 2, JE900BNC For model JE900BN, Put the dome cover to the housing well in right position, then tighten the two screws manually or with a screwdriver. (See the above figure at left) For Model JE900BNC embedded dome, Fit the three plastic pegs on the dome cover to the corresponding ones on the housing, then turn it to the right for about 20 degrees till it stops moving.
2-3 Housing and Wall-mount Bracket installation Push the power, video and controlling integrated cable through the bracket hole, then direct the top of the housing to the bracket hole and tighten them. Use a screwdriver to drive the three M6 screws on the bracket into the screw slot.
Select the where you want to installing and make sure the place can be sustained its weight. Pencil the relative positions of the three bores of the bracket on the ceiling, and fix the bracket to the ceiling with special screws (prepared by the user). Do not forget to push the connecting power, video and controlling cables through the cable outlet into the bracket tube in advance. Special Instruction: Pole bracket is used for indoor installation.
2-6 Installation for Embedded dome Camera Locations with suspended top suit the dome camera with in-ceiling installation style, which appears to be a hemisphere, having elegant-look and good concealment. The in-ceiling style installation applies to solid locations of the ceiling.
2-8 Running state test When you installed the dome camera and make sure the connecting is correct, you can power it on with the power supply DC14V (15V) for camera running state test. Once the power it on, check whether the power indicator led on the PCB board is on. Now the dome camera should be running self-check – panning, tilting and zooming. After the self-check, the position of the dome is horizontally on the left limiting position, tilt 30º. This means the PTZ camera is in good condition.
1. Address Setup As shown in the figure below, DIP-1 to DIP-8 of the 10-button coding switches is used to set up address of the dome camera from 1 to 63. Control can be realized only when address code of the dome camera is identical to that of the hard disk video recorder or matrix or controlling keyboard. The coding switches from DIP-1 to DIP-8 are equivalent to a 8-bit binary figure. The state “ON” of each bit means “1” while”OFF”means”0”.
No. 12345678 No. 12345678 No. 12345678 No.
3-3 The particular command and its Definition The below table is the particular short command for operate the PTZ camera with protocol “Pelco-D” and “Pelco-P” These short commands are useful for operation the PTZ function. Please remember Code No. Definition Code No.
c. Press the “PRESET” key B. Preview Preset Positions The function enables the dome camera to quickly return to the preset position you set. Enter the number you need to preview, Press the “PREVIEW” key, then the dome camera returns to the preset position. Example: Preview Preset position No.1 a. Enter “1” b. Press the “PREVIEW” key 1-5 Setup and running of Tour group Automatic tour function is a latest function of the constant-speed dome camera.
dome camera will automatically scan the preset positions set in the tour consecutively and circularly. Up to 16 preset positions can be saved in one tour group. A. Setup of Tours a. In the keyboard initial state, enter number “140”(110) and press the “PREVIEW” key to enter the tour setup. b. After entering the setup, add preset position number to the tour. Enter the preset position number and press the “PREVIEW” key, the first preset position is successfully added. Then goes the second one.
3.6.1 Setup of Left/right Limiting Positions The user can freely set one beginning position as Left Limiting Position and one terminal position as Right Limiting Position. (Remark: If the beginning position and the terminal position is the same position, the speed dome will scan for 360°). The Left/right limiting positions can be set up with keyboard controller. 1.1 Enter the number “160” (120) and press “PREVIEW” key to function the setup of left/right limiting positions 1.
3-8 Stop the auto scanning While the camera is carrying out auto scanning, if you want to stop the auto scanning, you can enter 138 (108) and press “PREVIEW” key or press “zoom+” “zoom-“ key to stop 3-9 The Setup, Activating and Exiting of Default Position The unit has a default position. The user can set up default position for a key monitoring area according to actual requirement. If not operated after 5 minutes, the dome camera will automatically monitor the default position. 1.
Part IV: Appendix Simple troubles and corresponding solutions Problems No action, no picture, indicator not on when power is switched on.
PART V. CONNECTING SKETCH Technical Support: owen.b52@gmail.
