User's Manual

IB for MD2400/MD2401/MD2420, 21-Apr-2006 Rev. 0
WRITTEN BY: DREAMIS SO PAGE:
17
Of
21
1. Make sure the phone is OFF (not in talk mode).
2. Use the CID/VOL (/\ or \/) button to scroll to the desired CID record.
3. Press the MEM key to display SELECT MEMORY 01-50.
4. Use the touch-tone pad to enter a memory location number (for example, press 01 to
store the record in memory location one).
NOTE: If the memory location is occupied, “REPLACE MEMO?” is displayed, and
you must confirm replacement by pressing the MEM button.
NOTE: Press the *EXIT button once to keep the previous setting and return to the
sub-menu.
Dialing a CID Number
While reviewing CID records, you may dial the phone number showing in the display.
1. Make sure the phone is OFF (not in talk mode).
2. Press CID/VOL (/\ or \/) button until the desired CID record shows in the display.
NOTE: Depending on (a) how the incoming caller’s phone number is formatted
when it is received, and (b) whether or not you previously pre-programmed your
local area code into the set up menu, you may need to adjust the format of the
incoming caller’s stored phone number before making the call.
Available formats include:
Number of digits Explanation Example
Eleven digits long distance code “1 ” 1-317-888-8888
+3-digit area code
+7-digit telephone number.
Ten digits 3-digit area code + 317-888-8888
7-digit telephone number.
Seven digits 7-digit telephone number. 888-8888
3. If the number does not dial as shown, press the format/conference button. Repeat if
necessary, until the correct number of digits show in the display.
4. Press the TALK/END/CALL BACK button on the handset. The number dials automatically.
NOTE: If the telephone number is corrupted, such as an alphabetical character
in a number field, you will hear an error tone and the number is not dialed. Unit
displays “UNABLE TO DIAL”.
Deleting a CID Record
1. Make sure the phone is OFF (not in talk mode).
2. Use the CID/VOL (/\ or \/) button to display the CID record you want to delete.
3. Press the DEL button. The display shows DELETE CALL ID?
4. Press the DEL button to erase the record showing in the display. The display
shows DELETED.
NOTE: Press the *EXIT key to return to the standby mode.
Deleting All CID Records
1. Make sure the phone is OFF (not in talk mode).
2. Use the CID/VOL (/\ or \/) button to scroll to any CID record.
3. Press and hold the DEL button until DELETE ALL? shows in the display.
4. Press DEL button to erase all of the current CID records. The display shows DELETED
followed by NO CALLS.
NOTE: Press the *EXIT key on the handset to return to the standby mode.
Changing the Battery
CAUTION: To reduce the risk of fire or personal injury, use only the battery that is compatible with this unit.
1. Make sure the telephone is OFF (not in talk mode) before you replace battery.
2. Remove the battery compartment cover.
3. Disconnect the cord attached to the battery pack from the jack inside the battery
compartment and remove the battery pack from the handset.
4. Insert the new battery pack and reconnect the battery plug.
5. Put the battery compartment cover back on.
6. Place handset in the base or handset charge cradle to charge. If you don’t charge the
handset battery properly (for 16 hours) when you first set up the phone and/or when you
install a new battery pack, the battery’s long-term performance will be compromised.
NOTE: If the battery is not properly installed in the handset, or if the battery pack is
not properly connected to the jack inside the battery compartment. “NO BATTERY”
shows in the display when the handset is placed in the charging cradle.
the jack inside the battery compartment.