User's Manual

IB for MD2400/MD2401/MD2420, 21-Apr-2006 Rev. 0
WRITTEN BY: DREAMIS SO PAGE:
12
Of
21
4. Press #PAUSE button again to save and display the new selection for a
few seconds.
Flash/Voice Mail
If you subscribe to the combined Call Waiting Caller ID service from your local telephone
company, you will receive Caller ID information (if available) on Call Waiting calls. During a
phone call, you will hear a beep to indicate another call is waiting on the line and Caller ID
information for the waiting call shows on the handset display.
• To connect to the waiting call, press the FLASH button on the handset, and your
original call is put on hold.
• To switch between the two calls, press the FLASH button.
TIP: Do not press the TALK button on the handset to activate a
custom calling service, such as call waiting, or call will disconnect.
If you subscribe to the voice mail service from your telco provider, you can press the Voice Mail button on the handset to retrieve the voice mail when there
is a voice mail in OFF mode. The antenna LED and the base voice mail LED will flashing if there is voice mail for indication.
Last Number Redial
You may redial a number up to 32 digits long.
To quickly redial the last number you dialed:
1. Press the TALK button.
2. Press the REDIAL button. -OR-
3. Press the REDIAL button first, then use the CID/VOL (/\ or \/) button to select the desired
redial number.
- Press the CID/VOL (/\ ) to review the oldest call and scroll toward the most recent calls
(higher numbers).
- Press the CID/VOL (\/ ) to review the newest call and scroll to older calls (lower numbers).
NOTE: You may choose from three last dialed numbers.
4. Press the TALK button. The number dials automatically.
If you get a busy signal and want to keep dialing the number, press the REDIAL button to
quickly redial the number.
Exit
Press the *EXIT button to exit a menu function and return to the standby screen.
Page
The page feature helps you locate a misplaced handset. To send and receive pages, all
handsets must be registered. If your handset is not registered, follow the instructions in
the Registration section of this manual.
Handset to Handset Paging (not apply on MD2400)
Dual handsets are respectively named as Handset 1 and Handset 2.
1. Make sure the phone is OFF (not in talk mode).
2. Press and release the PAGE/INT button on a handset. PAGING EXTENSION? shows in
the display.
3. Use the touch-tone pad to enter the handset number you want to page.
4. To cancel the page, press the *EXIT button.
Paging All Handsets from a Handset
1. Make sure the originating phone is OFF (not in talk mode).
2. Press and release the PAGE/INT button on a handset. PAGING EXTENSION? shows in
the display.
3. Use the touch-tone pad to enter the handset number you want to page. (1= to page
Handset 1, 2=to page handset 2, etc., and 5=to page all handsets)
4. To cancel the page, press the *EXIT or PAGE/INT button. On the originating handset,
you may press TALK.
Paging from the Base/Group Page
Use the base-only to page both registered handsets at the same time.
1. Press the page button on the base. All handsets beep for two minutes, and PAGING
FROM BASE shows on each handset’s display.
2. To cancel the page, press the page button on the base, or press the TALK button or the *EXIT button on each handset.
Mute
To have a private, off-line conversation, use the MUTE feature. The party on the telephone
line cannot hear you, but you can hear them.
1. Press the MUTE button. The handset display shows MUTE ON.
2. Press the MUTE button to cancel and return to your phone conversation.