User's Manual

5.
: - 重撥: Redial
- 對碼: Handset Regirstratoin
- 暫停: Pause
6.
: TALK/LINE
7.
: - 音量: Volume
- 來電: CID
- 去電: Recall
8.
: * / Next (Display remaining numbers)
9.
: - R: R Key
- 調時: Set Time (Date, Time setting)
-ON BASE
1. : In use
2. : Power up
3.
: Speaker/ hang up
4. : IP Speed Dial / Memory
5.
: - 設置: Program Setting
- 存儲: Memory Store
- 頻道: Channel
6.
: - 刪除: Delete
- 對碼: Handset Registration
7.
: - 對講: - Handset intercom with base
- Base paging handset
- 退出: Exit
8.
: - 音量: Volume
- 調時: Set Time (Date, Time setting)
9. : Hold
10.
: - 來電: CID
- 去電: Recall
11.
: - 重撥: Redial
- 暫停: Pause
12. : Flash
13. : * / Next (Display remaining numbers)
SET UP
TONE/PULSE DIALING
A TONE/PULSE switch which marked with “音頻/脈衝” is located at the
bottom of base, please choose the tone or pulse dialing format.
FLASH TIME SETTING
Flash time 100/300/600ms can be selected by switch located at the bottom
of base.
NOTE: The flash time default setting is 600ms, if you have any question
about the setting, please enquiry your telephone service provider.
DATE AND TIME SETTING ON BASE
1. Press and hold the
button for 2 seconds.
2. Press “▲” or “▼” button to adjust the month setting.
3. Press
button to go to date setting
4. Press “▲” or “▼” button to adjust the date.
5. Press
button to go to hour setting
6. Press “▲” or “▼” button to adjust the hour.
7. Press
button to go to minute setting
8. Press “▲” or “▼” button to adjust the minute.
9. Press
button again to confirm setting and go back to standby
mode.
10. Press
[退出] button to exit the program
DATE AND TIME SETTING ON HANDSET
Press and hold
button for 2 seconds to enter date and time setting.
CONTRAST SETTING SELECTION
1.
Press and hold [
存儲] button for 2 seconds.
2.
“LCd” shows in the display.
3.
Use the “▲” or “▼” button to adjust the level
4.
Press
to store selection.
5. Press
button to quit the program.
RINGER MELODY SELECTION
1.
Press and hold [
存儲] button for 2 seconds.
2.
Press [頻道] button until “ring” shows in the display.
3.
Use the “▲” or “▼” button to select the ringer. (5 ringer melodies
can be selected)
4.
Press
to store selection.
5.
Press
button to quit the program.
VIP RINGER MELODY SELECTION
1.
Press and hold [
存儲] button for 2 seconds.
2.
Press [頻道] / [查詢] button until “UIPring” shows in the
display.
3.
Use the “▲” or “▼” button to select the ringer. (5 ringer melodies
can be selected)
4.
Press
to store selection.
5.
Press
button to quit the program.
NOTE: This feature only works when you have subscribed to Caller ID
service.
PAGE RINGER MELODY SELECTION
1.
Press and hold [
存儲] button for 2 seconds.
2.
Press [ 頻道] / [ 查詢] button until “Intring” (Base) or
“PAgEring” (Handset) shows in the display.
3.
Use the “▲” or “▼” button to select the ringer (5 ringer melodies
can be selected)
4.
Press
to store selection.
5.
Press
button to quit the program.
RINGER ON/OFF
Ringer ON
1.
Press and hold [
存儲] button for 2 seconds.
2.
Press [頻道] / [查詢] button until “ringUol” shows in the
display.
3.
Use the “▲” or “▼” button to volume level 1 or 2.
4.
Press
to store selection.
Ringer OFF
1.
Press and hold [
存儲] button for 2 seconds.
2.
Press [頻道] / [查詢] button until “ringUol” shows in the
display.
3.
Use the “▲” or “▼” button to select OFF.
4.
Press
to store selection and “免打擾” will show in
display.
LOCAL AREA CODE SETTING
If local PSTN still sends the CID with local area code attached, it is
necessary to filter out the local area code when dial back from CID log.
The function is to remove the local area code hence the local CID will be
appeared on the CID log with local area code deleted. For example: local
CID received shows “07552288788”, set the 0755 as local area code then
it becomes “2288788” next time receive it. If LCD shows “7552288788”, set
the “755-“ as local area code.
1.
Press and hold [
存儲] button for 2 seconds.
2.
Press [頻道] / [查詢] button until “CodE” shows in the
display.
3.
Enter (1-4) area code digit, if you make a mistake, press
button to backspace
4.
Press
to store the setting.
5.
Press
button to quit the program.
LONG DISTANCE CODE PROGRAMMING CID LOG EDITING BEFORE
DIAL OUT
For example: a long distance caller ID “013928389222” will only display
“13928389222” with “0” deleted. This function will activate the “0” insertion
hence it will show correctly the call is a long distance call
1.
Press [
來電] button.
2.
Press the “▲” or “▼” button, to review CID record.
3. Enter digit “0”.
4.
Press
to backspace left hand side number if you make a
mistake.
5.
Press
button on handset or button on base to dial out
the number.
6.
Press the “▲” or “▼” button to back to the record during edit. Or
press
button to quit the program.
INSERTING PREFIX IN PHONE BOOK RECORD
1.
Press [
存儲] button, then press the desired memory location
number (01 through 16) in 2 digits.
2.
Or press [
頻道] / [查詢] button, “存儲” shows in the display.
3.
Press the “▲” or “▼” button, to review the memory.
4.
Enter one-digit number. (For example: If you need dial “9” for
external line dialing out, then you need enter digit “9”)
5.
Press
to backspace the digit if you make a mistake.
6.
Press
button on handset or button on base to dial out
the number.
7.
Press the “▲” or “▼” button to back to record during edit. Or press
button to quit the program.
HANDSET REGISTRATION
The ex-factory cordless handset had already registered by default. If you
can’t linkup the handset and base or if you brought expandable handset,
please follow below instruction to register the handsets (include ex-factory
headset).
NOTE: Maximum 4 handsets can be registered in one base unit. During in
register procedures, handsets should be placed near the base unit.
1. Press and hold
[對碼] button on base to enter the registration mode.
Display shows text “CodE HS-1“. (Don’t release the button until all
handsets had been registered.)
2. Then, press and hold
[對碼] button on cordless handset. (Handset
display shows text “HS –1 “ and base display shows “COdE HS-2”.
Keep holding the REGISTER buttons on handset even a confirmation
beep is heard from base, it means it can press
button on
another handset (handset displays “HS-2”, Base displays “CodE
HS-3”) After registration, release the [對碼] button on handset and
then release the [對碼] button on base.)
VOLUME
HANDSET
While you are on phone, you can press the [音量] “▲” or “▼” button to
adjust the volume of the handset’s earpiece.
BASE
When you are on phone by using the speakerphone, press
button
to adjust the volume of the speakerphone volume.
RECEIVING A CALL
BASE
1. Press
button or pick up the corded handset.
2. Press
button or put the corded handset on the cradle of base to
hang up.
HANDSET
1. Press
button to pick up the call.