User Manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 1.1 Package contents
- 1.2 Product Features
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WLAN Broadband Router
- 3.2 Connect to the WLAN Broadband Router
- 3.3 Management and configuration on the WLAN Broadband Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Site Survey
- 3.3.10 WPS
- 3.3.11 Schedule
- 3.3.12 LAN Interface Setup
- 3.3.13 WAN Interface Setup
- 3.3.14 Firewall - Port Filtering
- 3.3.15 Firewall - IP Filtering
- 3.3.16 Firewall - MAC Filtering
- 3.3.17 Firewall - Port Forwarding
- 3.3.18 Firewall – URL Filtering
- 3.3.19 Firewall - DMZ
- 3.3.20 QoS
- 3.3.21 Management - Statistics
- 3.3.22 Management - DDNS
- 3.3.23 Management - Time Zone Setting
- 3.3.24 Management – Denial-of-Service
- 3.3.25 Management - Log
- 3.3.26 Management - Upgrade Firmware
- 3.3.27 Management Save/ Reload Settings
- 3.3.28 Management - Password Setup
- 3.3.29 Management – Watchdog Setting
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WLAN BROADBAND ROUTER Version: 1.0
37
Password If you select the PPPoE support on WAN interface, fill in
the user name and password to login the PPPoE server.
Service Name Fill in the service name of Service Name. The default
value is empty.
Connection Type Select the connection type from pull-down menu. There
are Continuous, Connect on Demand and Manual three
types to select.
Continuous connection type means to setup the
connection through PPPoE protocol whenever this
WLAN Broadband Router is powered on.
Connect on Demand connection type means to setup the
connection through PPPoE protocol whenever you send
the data packets out through the WAN interface; there are
a watchdog implemented to close the PPPoE connection
while there are no data sent out longer than the idle time
set.
Manual connection type means to setup the connection
through the PPPoE protocol by clicking the Connect
button manually, and clicking the Disconnect button
manually.
Idle Time If you select the PPPoE and Connect on Demand
connection type, fill in the idle time for auto-disconnect
function. Value can be between 1 and 1000 minutes.
MTU Size Fill in the mtu size of MTU Size. The default value is
1452. Refer to 4.23 What is Maximum Transmission Unit
(MTU) Size?
Attain DNS
Automatically
Click to select getting DNS address for PPPoE support.
Please select Set DNS Manually if the PPPoE support is
selected.
Set DNS Manually Click to select getting DNS address for Static IP support.
DNS 1 Fill in the IP address of Domain Name Server 1.
DNS 2 Fill in the IP address of Domain Name Server 2.
DNS 3 Fill in the IP address of Domain Name Server 3.
Clone MAC Address Fill in the MAC address that is the MAC address to be
cloned. Refer to 4.24 What is Clone MAC Address?
Enable uPNP Click the checkbox to enable uPNP function.