User Manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 1.1 Package contents
- 1.2 Product Features
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WLAN Broadband Router
- 3.2 Connect to the WLAN Broadband Router
- 3.3 Management and configuration on the WLAN Broadband Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Site Survey
- 3.3.10 WPS
- 3.3.11 Schedule
- 3.3.12 LAN Interface Setup
- 3.3.13 WAN Interface Setup
- 3.3.14 Firewall - Port Filtering
- 3.3.15 Firewall - IP Filtering
- 3.3.16 Firewall - MAC Filtering
- 3.3.17 Firewall - Port Forwarding
- 3.3.18 Firewall – URL Filtering
- 3.3.19 Firewall - DMZ
- 3.3.20 QoS
- 3.3.21 Management - Statistics
- 3.3.22 Management - DDNS
- 3.3.23 Management - Time Zone Setting
- 3.3.24 Management – Denial-of-Service
- 3.3.25 Management - Log
- 3.3.26 Management - Upgrade Firmware
- 3.3.27 Management Save/ Reload Settings
- 3.3.28 Management - Password Setup
- 3.3.29 Management – Watchdog Setting
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WLAN BROADBAND ROUTER Version: 1.0
22
registered in the access control list can link to this
WLAN Broadband Router.
MAC Address Fill in the MAC address of client to register this WLAN
Broadband Router access capability.
Comment Fill in the comment tag for the registered client.
Apply Changes Click the Apply Changes button to register the client to
new configuration setting.
Reset Click the Reset button to abort change and recover the
previous configuration setting.
Current Access Control
List
It shows the registered clients that are allowed to link to
this WLAN Broadband Router.
Delete Selected Click to delete the selected clients that will be access
right removed from this WLAN Broadband Router.
Delete All Click to delete all the registered clients from the access
allowed list.
Reset Click the Reset button to abort change and recover the
previous configuration setting.
3.3.8 WDS Settings
Wireless Distribution System uses wireless media to communicate with other
APs, like the Ethernet does. To do this, you must set these APs in the same
channel and set MAC address of other AP that you want to communicate with in
the table and then enable the WDS.