User Manual
Table Of Contents
- Revision History
- Terminology
- 1 Introduction
- 1.1 Package contents
- 1.2 Product Features
- 2 Installation
- 3 Software configuration
- 3.1 Prepare your PC to configure the WLAN Broadband Router
- 3.2 Connect to the WLAN Broadband Router
- 3.3 Management and configuration on the WLAN Broadband Router
- 3.3.1 Status
- 3.3.2 Setup Wizard
- 3.3.3 Operation Mode
- 3.3.4 Wireless - Basic Settings
- 3.3.5 Wireless - Advanced Settings
- 3.3.6 Wireless - Security Setup
- 3.3.7 Wireless - Access Control
- 3.3.8 WDS Settings
- 3.3.9 Site Survey
- 3.3.10 WPS
- 3.3.11 Schedule
- 3.3.12 LAN Interface Setup
- 3.3.13 WAN Interface Setup
- 3.3.14 Firewall - Port Filtering
- 3.3.15 Firewall - IP Filtering
- 3.3.16 Firewall - MAC Filtering
- 3.3.17 Firewall - Port Forwarding
- 3.3.18 Firewall – URL Filtering
- 3.3.19 Firewall - DMZ
- 3.3.20 QoS
- 3.3.21 Management - Statistics
- 3.3.22 Management - DDNS
- 3.3.23 Management - Time Zone Setting
- 3.3.24 Management – Denial-of-Service
- 3.3.25 Management - Log
- 3.3.26 Management - Upgrade Firmware
- 3.3.27 Management Save/ Reload Settings
- 3.3.28 Management - Password Setup
- 3.3.29 Management – Watchdog Setting
- 4 Frequently Asked Questions (FAQ)
- 4.1 What and how to find my PC’s IP and MAC address?
- 4.2 What is Wireless LAN?
- 4.3 What are ISM bands?
- 4.4 How does wireless networking work?
- 4.5 What is BSSID?
- 4.6 What is ESSID?
- 4.7 What are potential factors that may causes interference?
- 4.8 What are the Open System and Shared Key authentications?
- 4.9 What is WEP?
- 4.10 What is Fragment Threshold?
- 4.11 What is RTS (Request To Send) Threshold?
- 4.12 What is Beacon Interval?
- 4.13 What is Preamble Type?
- 4.14 What is SSID Broadcast?
- 4.15 What is Wi-Fi Protected Access (WPA)?
- 4.16 What is WPA2?
- 4.17 What is 802.1x Authentication?
- 4.18 What is Temporal Key Integrity Protocol (TKIP)?
- 4.19 What is Advanced Encryption Standard (AES)?
- 4.20 What is Inter-Access Point Protocol (IAPP)?
- 4.21 What is Wireless Distribution System (WDS)?
- 4.22 What is Universal Plug and Play (uPNP)?
- 4.23 What is Maximum Transmission Unit (MTU) Size?
- 4.24 What is Clone MAC Address?
- 4.25 What is DDNS?
- 4.26 What is NTP Client?
- 4.27 What is VPN?
- 4.28 What is IPSEC?
- 4.29 What is WLAN Block Relay Between Clients?
- 4.30 What is WMM?
- 4.31 What is WLAN ACK TIMOUT?
- 4.32 What is Modulation Coding Scheme (MCS)?
- 4.33 What is Frame Aggregation?
- 4.34 What is Guard Intervals (GI)?
- 5 Configuration Examples
USER’S MANUAL OF WLAN BROADBAND ROUTER Version: 1.0
8
properties.
3. In Local Area Connection Properties window, Choose Networking tab, move mouse
and click Internet Protocol Version 4 (TCP/IPv4), then click Properties button.
4. Move mouse and click General tab, Select Specify an IP address and type in values
as following example.
9 IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is
good to connect the Wireless LAN Access Point.
9 IP Subnet Mask: 255.255.255.0
5. Click OK to complete the IP parameters setting.
3.2 Connect to the WLAN Broadband Router
Open a WEB browser, i.e. Microsoft Internet Explore 6.1 SP1 or above, then enter
192.168.1.254 on the URL to connect the WLAN Broadband Router.
3.3 Management and configuration on the WLAN Broadband Router
3.3.1 Status
This page shows the current status and some basic settings of the device, includes
system, wireless, Ethernet LAN and WAN configuration information.